body_transfer
sketch
  inputs:
    Angle = sketch.angle (Angle)
    Offset = sketch.offset (Length)
  expressions: sketch.angle, sketch.offset
sketch_along_path
  inputs:
    Distance (0 to 1) = sketch.t (Unitless)
  expressions: sketch.t
extrude
  inputs:
    Distance = extrude.distance (Length)
    Distance 2 = extrude.distance2 (Length)
    Start offset = extrude.start_offset (Length)
    Taper angle = extrude.taper (Angle)
    To offset = extrude.to_offset (Length)
  expressions: extrude.distance, extrude.distance2, extrude.start_offset, extrude.taper, extrude.to_offset
extrude_thin
  inputs:
    Distance = thin.distance (Length)
    Distance 2 = thin.distance2 (Length)
    Start offset = thin.start_offset (Length)
    Taper angle = thin.taper (Angle)
    To offset = thin.to_offset (Length)
    Thickness = thin.thickness (Length)
    Thickness 2 = thin.thickness2 (Length)
  expressions: thin.distance, thin.distance2, thin.start_offset, thin.taper, thin.to_offset, thin.thickness, thin.thickness2
revolve
  inputs:
    Angle = revolve.angle (Angle)
    Angle 2 = revolve.angle2 (Angle)
  expressions: revolve.angle, revolve.angle2
fillet_constant
  inputs:
    Radius = fillet.radius (Length)
  expressions: fillet.radius
fillet_chord
  inputs:
    Chord length = fillet.radius (Length)
  expressions: fillet.radius
fillet_curvature
  inputs:
    Equivalent radius = fillet.radius (Length)
  expressions: fillet.radius
fillet_variable
  inputs:
    Start radius = fillet.radius (Length)
    End radius = fillet.radius2 (Length)
    Mid radius = fillet.mid (Length)
  expressions: fillet.radius, fillet.radius2, fillet.mid
fillet_spline
  inputs:
    Start radius = fillet.radius (Length)
    Control radius = fillet.r1 (Length)
    Control radius = fillet.r2 (Length)
    End radius = fillet.r3 (Length)
  expressions: fillet.radius, fillet.r1, fillet.r2, fillet.r3
chamfer
  inputs:
    Distance = chamfer.distance (Length)
    Distance 2 = chamfer.distance2 (Length)
    Angle = chamfer.angle (Angle)
  expressions: chamfer.distance, chamfer.distance2, chamfer.angle
box
  inputs:
    Length = box.length (Length)
    Width = box.width (Length)
    Height = box.height (Length)
  expressions: box.length, box.width, box.height, box.x, box.y, box.z
cylinder
  inputs:
    Radius = cyl.radius (Length)
    Height = cyl.height (Length)
  expressions: cyl.radius, cyl.height, cyl.x, cyl.y, cyl.z
sphere
  inputs:
    Radius = sph.radius (Length)
  expressions: sph.radius, sph.x, sph.y, sph.z
torus
  inputs:
    Major radius = tor.major (Length)
    Minor radius = tor.minor (Length)
  expressions: tor.major, tor.minor, tor.x, tor.y, tor.z
combine
pattern_rectangular
  inputs:
    Quantity = rect.count1 (Unitless)
    Spacing = rect.spacing1 (Length)
    Quantity 2 = rect.count2 (Unitless)
    Spacing 2 = rect.spacing2 (Length)
  expressions: rect.count1, rect.spacing1, rect.count2, rect.spacing2
pattern_circular
  inputs:
    Quantity = circ.count (Unitless)
    Total angle = circ.angle (Angle)
  expressions: circ.count, circ.angle
pattern_path
  inputs:
    Quantity = path.count (Unitless)
    Distance = path.spacing (Length)
  expressions: path.count, path.spacing
mirror
  inputs:
    Angle = mirror.angle (Angle)
    Offset = mirror.offset (Length)
  expressions: mirror.angle, mirror.offset
hole_simple
  inputs:
    Diameter = hole.diameter (Length)
    Depth = hole.depth (Length)
  expressions: hole.diameter, hole.depth
hole_drilled
  inputs:
    Diameter = hole.diameter (Length)
    Depth = hole.depth (Length)
    Tip angle = hole.tip_angle (Angle)
  expressions: hole.diameter, hole.depth, hole.tip_angle
hole_counterbore
  inputs:
    Diameter = hole.diameter (Length)
    Depth = hole.depth (Length)
    Counterbore diameter = hole.cb_diameter (Length)
    Counterbore depth = hole.cb_depth (Length)
  expressions: hole.diameter, hole.depth, hole.cb_diameter, hole.cb_depth
hole_countersink
  inputs:
    Diameter = hole.diameter (Length)
    Depth = hole.depth (Length)
    Countersink diameter = hole.cs_diameter (Length)
    Countersink angle = hole.cs_angle (Angle)
  expressions: hole.diameter, hole.depth, hole.cs_diameter, hole.cs_angle
thread
  inputs:
    Length = thread.length (Length)
  expressions: thread.length
loft
sweep
sweep_options
  inputs:
    Twist = sweep.twist (Angle)
    Scale = sweep.scale (Unitless)
  expressions: sweep.twist, sweep.scale
shell
  inputs:
    Thickness = shell.thickness (Length)
  expressions: shell.thickness
draft
  inputs:
    Angle = draft.angle (Angle)
    Angle = draft_neutral.angle (Angle)
    Offset = draft_neutral.offset (Length)
  expressions: draft.angle, draft_neutral.angle, draft_neutral.offset
construction_plane
  inputs:
    Angle = cplane.angle (Angle)
    Offset = cplane.offset (Length)
  expressions: cplane.angle, cplane.offset
split
  inputs:
    Angle = split.angle (Angle)
    Offset = split.offset (Length)
  expressions: split.angle, split.offset
split_line
  inputs:
    Angle = split_line.angle (Angle)
    Offset = split_line.offset (Length)
  expressions: split_line.angle, split_line.offset
construction_axis
  inputs:
    Angle = axis_a.angle (Angle)
    Offset = axis_a.offset (Length)
    Angle = axis_b.angle (Angle)
    Offset = axis_b.offset (Length)
  expressions: axis_a.angle, axis_a.offset, axis_b.angle, axis_b.offset
construction_point_planes
  inputs:
    Angle = pt_a.angle (Angle)
    Offset = pt_a.offset (Length)
    Angle = pt_b.angle (Angle)
    Offset = pt_b.offset (Length)
    Angle = pt_c.angle (Angle)
    Offset = pt_c.offset (Length)
  expressions: pt_a.angle, pt_a.offset, pt_b.angle, pt_b.offset, pt_c.angle, pt_c.offset
construction_point_along
  inputs:
    Distance (0 to 1) = pt.t (Unitless)
  expressions: pt.t
split_face
  inputs:
    Angle = split_face.angle (Angle)
    Offset = split_face.offset (Length)
  expressions: split_face.angle, split_face.offset
scale
  inputs:
    Scale factor = scale.factor (Unitless)
    X scale = scale.x (Unitless)
    Y scale = scale.y (Unitless)
    Z scale = scale.z (Unitless)
  expressions: scale.factor, scale.x, scale.y, scale.z
offset_face
  inputs:
    Distance = offset_face.distance (Length)
  expressions: offset_face.distance
delete_face
bounding_solid
  inputs:
    Margin = bounding.margin (Length)
  expressions: bounding.margin
pipe
  inputs:
    Diameter = pipe.diameter (Length)
    Wall = pipe.wall (Length)
  expressions: pipe.diameter, pipe.wall
emboss
  inputs:
    Depth = emboss.depth (Length)
  expressions: emboss.depth
rib
  inputs:
    Thickness = rib.thickness (Length)
    Depth = rib.depth (Length)
  expressions: rib.thickness, rib.depth
replace_face
  inputs:
    Angle = replace_face.angle (Angle)
    Offset = replace_face.offset (Length)
  expressions: replace_face.angle, replace_face.offset
align
coil
  inputs:
    Diameter = coil.diameter (Length)
    Pitch = coil.pitch (Length)
    Revolutions = coil.turns (Unitless)
    Section size = coil.section_size (Length)
    Start angle = coil.start_angle (Angle)
  expressions: coil.diameter, coil.pitch, coil.turns, coil.section_size, coil.start_angle, coil.x, coil.y, coil.z
sheet_base
sheet_contour
  inputs:
    Distance = contour.distance (Length)
  expressions: contour.distance
sheet_flange
  inputs:
    Height = flange.height (Length)
    Angle = flange.angle (Angle)
    Bend radius = flange.radius (Length)
    Edge angle = flange.e1_angle (Angle)
    Edge height = flange.e1_height (Length)
    Edge height = flange.e2_height (Length)
    Corner relief = flange.relief (Length)
  expressions: flange.height, flange.angle, flange.radius, flange.e1_angle, flange.e1_height, flange.e2_height, flange.relief
sheet_hem
  inputs:
    Length = hem.length (Length)
    Gap = hem.gap (Length)
  expressions: hem.length, hem.gap
sheet_perforate
  inputs:
    Diameter = perforate.diameter (Length)
    Pitch = perforate.pitch (Length)
    Margin = perforate.margin (Length)
  expressions: perforate.diameter, perforate.pitch, perforate.margin
sheet_fold
  inputs:
    Angle = fold.angle (Angle)
    Bend radius = fold.radius (Length)
  expressions: fold.angle, fold.radius
sheet_unfold
sheet_convert
boss
  inputs:
    Diameter = boss.diameter (Length)
    Height = boss.height (Length)
    Hole diameter = boss.hole_diameter (Length)
    Hole depth = boss.hole_depth (Length)
    Draft angle = boss.draft (Angle)
    Root fillet = boss.fillet (Length)
    Ribs = boss.ribs (Unitless)
    Rib thickness = boss.rib_thickness (Length)
    Rib length = boss.rib_length (Length)
    Rib offset = boss.rib_offset (Length)
  expressions: boss.diameter, boss.height, boss.hole_diameter, boss.hole_depth, boss.draft, boss.fillet, boss.ribs, boss.rib_thickness, boss.rib_length, boss.rib_offset
lip
  inputs:
    Width = lip.width (Length)
    Height = lip.height (Length)
    Gap = lip.gap (Length)
  expressions: lip.width, lip.height, lip.gap
snap_fit
  inputs:
    Length = snap.length (Length)
    Thickness = snap.thickness (Length)
    Width = snap.width (Length)
    Catch depth = snap.catch_depth (Length)
    Catch length = snap.catch_length (Length)
  expressions: snap.length, snap.thickness, snap.width, snap.catch_depth, snap.catch_length
rest
  inputs:
    Width = rest.width (Length)
    Height = rest.height (Length)
    Length = rest.length (Length)
    Draft angle = rest.draft (Angle)
    Wall thickness = rest.thickness (Length)
  expressions: rest.width, rest.height, rest.length, rest.draft, rest.thickness
boundary_fill
remove
patch
stitch
  inputs:
    Tolerance = stitch.tolerance (Length)
  expressions: stitch.tolerance
thicken
  inputs:
    Thickness = thicken.thickness (Length)
  expressions: thicken.thickness
surface_extrude
  inputs:
    Distance = surface_extrude.distance (Length)
    Distance 2 = surface_extrude.distance2 (Length)
    Start offset = surface_extrude.start_offset (Length)
    Taper angle = surface_extrude.taper (Angle)
    To offset = surface_extrude.to_offset (Length)
  expressions: surface_extrude.distance, surface_extrude.distance2, surface_extrude.start_offset, surface_extrude.taper, surface_extrude.to_offset
surface_revolve
  inputs:
    Angle = srev.angle (Angle)
    Angle 2 = srev.angle2 (Angle)
  expressions: srev.angle, srev.angle2
surface_sweep
surface_sweep_options
  inputs:
    Twist = surface_sweep.twist (Angle)
    Scale = surface_sweep.scale (Unitless)
  expressions: surface_sweep.twist, surface_sweep.scale
surface_loft
surface_blend
surface_offset
  inputs:
    Distance = soff.distance (Length)
    Tolerance = soff.tolerance (Length)
  expressions: soff.distance, soff.tolerance
surface_blend
surface_boundary
surface_match
surface_fair
  inputs:
    Tolerance = sfair.tolerance (Length)
  expressions: sfair.tolerance
unstitch
reverse_normal
surface_untrim
surface_extend
  inputs:
    Distance = extend.distance (Length)
  expressions: extend.distance
surface_extend_to_plane
  inputs:
    Distance = extend.distance (Length)
    Angle = extend.angle (Angle)
    Offset = extend.offset (Length)
  expressions: extend.distance, extend.angle, extend.offset
surface_extend_to_face
  inputs:
    Distance = extend.distance (Length)
  expressions: extend.distance
surface_ruled
  inputs:
    Distance = ruled.distance (Length)
    Angle = ruled.angle (Angle)
  expressions: ruled.distance, ruled.angle
surface_trim
  inputs:
    Angle = trim.angle (Angle)
    Offset = trim.offset (Length)
  expressions: trim.angle, trim.offset
move
  inputs:
    X distance = move.x (Length)
    Y distance = move.y (Length)
    Z distance = move.z (Length)
    Angle = move.angle (Angle)
  expressions: move.x, move.y, move.z, move.angle
import
mesh_convert
  inputs:
    Tolerance = mesh_convert.tolerance (Length)
  expressions: mesh_convert.tolerance
mesh_import
