A PR that saves something new adds crates/doc/src/format/pending/<name>.rs (a note, and an upgrade step if older designs must be rewritten). The build writes the next format number while changes are pending and lists them in format_pending; scripts/fold-format-pending.sh fixes them as v<N>/ at release time. Formats 23 and 24 move into v23/ and v24/.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
An Edge Flange feature can set the shape and size of the relief at the corners its flanges make, in place of the sheet metal rule's. Design format 24.
Co-authored-by: NOWN-DEV <[email protected]>
Co-Authored-By: Claude Sonnet 5.5 <[email protected]>
FreeCAD .FCStd and Rhino .3dm files open, insert and drop like STEP and IGES:
cadmpeg (Apache-2.0, pinned =0.6.1, native builds only) detects the format,
decodes it under its service resource caps, validates the model and writes it
as STEP AP214, which becomes an Import feature in a new component named after
the file, with the up and names options.
Only the fcstd, rhino and step codecs are compiled in (no default features).
ACIS is left out: cadmpeg's sat codec is a ShapeManager stream decoder.
native_cad.rs is the single importer seam. Self-made FreeCAD and Rhino box
fixtures, hostile-input, ZIP-bomb and cap tests, engine tests for the
component path; the browser build reports these formats as not supported.
A note under design format 23 says an Import's file can name these formats.
Co-authored-by: Jacob Oursland <[email protected]>
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Thin extrude caps are certified by the curves the wall follows, so a sketch attached to a cap survives switching between solid and thin (#1519).
Co-Authored-By: Philipp Bischoff <[email protected]>
Co-Authored-By: Claude Sonnet 5.5 <[email protected]>
Motion links can carry a coupling (gear pair, rack and pinion, screw) whose ratio follows radii, picked round faces or pitch. Design format 23.
Co-authored-by: SychPL <[email protected]>
Co-Authored-By: Claude Sonnet 5.5 <[email protected]>
The product preview asked the viewport executor for the full physical
viewport, so a maximised 4K window (~8 MP) was refused against the 4 MP
limit on every frame. The preview now draws at the largest size of the
same aspect the executor admits (RenderLimits::fit, scratch included)
and filters it up into the viewport through the existing offscreen
blit. Viewports within the limits still draw at full size.
PNG setups past the image limits now say what the limits are and the
largest size at that aspect, and the image panel offers to use it.
Co-authored-by: Claude Opus 5.5 <[email protected]>
A sketch text's height, place (x and y) and angle can each be an expression over the design's parameters, and the text follows parameter changes, undo and reopening. Closes#1362.
Co-authored-by: NOWN-DEV <[email protected]>
The continuity core (kernel bridge: Hermite control rows reproducing a support surface's position, tangent, curvature and change of curvature, G0 to G3), surface.blend between two edge chains (#764), and a crown for fitted patches. Existing patches and fillets are unchanged by default (crown 0 is the plain patch bit for bit). SurfaceBlend and Patch.crown are noted under format 22.
Material-card validation now names the exact condition fields missing for each property (missing_condition_fields), alongside the existing unspecified_conditions.
Co-authored-by: 0xlillith <[email protected]>
joint.motion_link offset is read in the linked value's units (degrees or mm, or an expression); links are still stored in radians, so saved designs open unchanged. A new joint whose values fall outside its limits starts at the nearer limit, stores it, and says so in warnings. Loop dof also counts at a nearby pose, so a part at a dead point of its loop keeps its mobility. The mechanisms skill is updated to match.
JIJINBEI