The continuity core (kernel bridge: Hermite control rows reproducing a support surface's position, tangent, curvature and change of curvature, G0 to G3), surface.blend between two edge chains (#764), and a crown for fitted patches. Existing patches and fillets are unchanged by default (crown 0 is the plain patch bit for bit). SurfaceBlend and Patch.crown are noted under format 22.
Part of #771 and #772. solid.sweep and surface.sweep take orientation (perpendicular, parallel or a direction), twist (up to 4 turns) and end scale (0.01 to 100), applied about the profile's normal through the path's start; default options run the old sweep, so existing sweeps are unchanged. New fields are optional, left out when unset and noted under format 21; twist and scale are model parameters. Both sweep dialogs get Orientation, Twist and End Scale rows; labels in every catalog. Checked on main + this branch: cargo check --workspace, kernel/engine/UI sweep tests, the doc suite and the robustness goldens.
Extend works on any surface: natural (continuing the face's own surface), tangent (G1 run-off) or curvature (G2 run-off), by a distance, up to a plane or face, or back to the surface's bounds, with neighbouring edges lengthened to meet. Untrim and Extend share face parameter-loop helpers. The new SurfaceExtend fields are noted under format 21. Closes#760.
Ruled Surface: strips off an edge chain in normal, tangent, angle or direction mode, exact planes/cylinders/cones where possible, mitred or round corners, stitched into one surface body. SurfaceRuled is noted under format 21. Closes#762.
Part 2 of #876: one walk over the references a feature holds (the sketches it's built from, the features it names, the bodies it works on) replaces three hand-written matches, with a golden record covering every variant.
Offsets picked faces along their normals into a new surface body: planes and cylinders move exactly, other faces get a fitted B-spline within tolerance, and offsets that would fold over are refused. Adds the SurfaceOffset feature (noted under format 18), the surface.offset engine command and an Offset Surface dialog.
Closes#758.
Co-authored-by: jyviko <[email protected]>
Each wall of a surface built from sketch curves (Surface Extrude, Revolve, Sweep and Loft) is now named after the curve it comes from, exactly rather than from geometry, so references to those faces survive edits.
Surface Loft lofts open or closed curve chains, one section per sketch in pick order, into surface bodies. Adds the SurfaceLoft feature (format 18 note), the surface.loft command, a dialog with Edit Feature support, and kernel and engine tests.
Part of #757.
Surface Sweep carries open curves and closed profile boundaries along a sketch path into surface bodies, with smooth walls along curved point paths. Adds the SurfaceSweep feature (format 18 note), the surface.sweep command, a dialog with Edit Feature support, and kernel and engine tests.
Part of #757.
Surface Revolve turns open curves and closed profile boundaries about a sketch axis into surface bodies, with cone apexes and sphere poles where a chain ends on the axis, and a closed shell made solid. Adds the SurfaceRevolve feature (format 18 note), the surface.revolve command, a dialog with Edit Feature support and analytic kernel and engine tests.
Part of #757.
Delete Face takes heal (default true, as before). With heal: false the picked faces are removed and the gap stays open, leaving the remaining faces as a surface body (kernel remove_faces); deleting every face is refused. Saved only when false, noted under format 18.
surface.extrude sweeps open curve chains and profile boundaries along the sketch normal into a surface body (walls only, no caps). Saved under format 17.
Refs #757
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Icons for the surface toolset, and its planned commands registered and disabled with the issue that tracks each one.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Add a one-surface fill of closed 3D loops to geom
A closed loop of curves that does not lie in a plane has no exact surface;
the usual answer is one smooth face fitted over it. fill_loop does that:
- the loop's best-fit plane (Newell normal), with a frame chosen from the
loop itself so the result does not depend on where the loop starts, its
direction, or where the part sits
- the loop seen along that normal must be simple and must not fold or run
along the normal; otherwise it is refused ("not supported yet"), never
filled with wrong geometry
- one non-rational bicubic B-spline height field over the loop's box,
fitted by least squares to the loop's samples (The NURBS Book 9.4.1,
9.4.3, eq. 9.62/9.65) with a thin-plate smoothness term
lambda*A*int(h_uu^2 + 2 h_uv^2 + h_vv^2), A one grid cell's area, so the
fit is the same at any scale; only planes are reproduced exactly
- span counts per direction (long narrow loops fit), refined until the
loop is within tolerance, else refused with the deviation reached
bspline: bisected span search, basis functions on a stack array, one
clamping helper shared by curves and surfaces, one binomial helper.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01J53sR6gEaVt56soFDpTck8
* Patch fills non-planar loops of edges with one smooth face (#250)
surface.patch with edges refused any loop that is not planar ("not
supported yet: patching a loop that is not planar"). It now fills it:
- planar loops still get one exact planar face, but planarity is certified
conservatively: lines by their ends, B-spline/NURBS edges by their control
points, intersection curves by their samples lying on a support plane
within tolerance; a loop that can't be certified is filled instead
- other loops get one face from geom's fill_loop, bounded by the body's own
chained edges, whole (no split): its history is one generated face whose
edges are the body's, and it stitches back into a closed solid
- intersection-curve edges are sampled by a seeded, guarded double
projection shared by the planarity test and the fill (plane_fit)
- the face tolerance is 10x the planarity tolerance (documented: later
operations take the face to contain its edges within it)
- edge picking runs inside the guard; the geom->truck conversion is shared
with the T-spline sheets (spline_conv); the Newell plane fit is shared with
STEP import
Tests: 3- to 8-sided, concave (dart, arrow, plus), flat-corner, two-edge and
imported rims fill as one face and stitch closed (volumes against an
independent integral); finite mesh normals, same result for any pick order
or placement; non-height-field loops and too-fine detail are refused.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01J53sR6gEaVt56soFDpTck8
* Test the Patch dialog filling a non-planar loop of picked edges
The Patch dialog's only test used a sketch profile. Picking the four
curved rim edges of a box cut by a sideways cylinder now makes one
surface.patch command whose result is a single smooth face over the rim.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01J53sR6gEaVt56soFDpTck8
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
The old ids live only in crates/engine/src/legacy_ids.rs (the legacy migration table): find_command maps them, so old scripts, recipes and control calls keep working, and saved shortcuts, recent and pinned commands are migrated on load (designs store no command ids). Parity maps the observed catalog ids to ours through xtask/data/fusion-ids.tsv. The agent rule now reads: our own dotted id, never another product's. Cargo.toml's repository points at github.com/bherbruck/solvecraft.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Kernel extend(body, edges, distance) moves the picked straight edges of a
planar surface outward in its plane, with neighbours meeting them. Doc
feature SurfaceExtend, engine FusionExtendCommand. Tests: 10x10 extended
by 5 past one edge gives 150, past two gives 225; the engine patch, trim,
extend and thicken gives 240.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01AS5Tn3xieewUSg3uxrMVdL
Kernel (surfaces):
- Bodies with an open shell are surface bodies (Body::is_surface).
- patch_region: a planar patch of a sketch region. patch_edges: a planar
patch filling a closed loop of a body's edges.
- copy_faces: faces copied out as a surface.
- stitch: sew surfaces along coinciding edges, turning faces to agree; the
result is a solid when it closes.
- trim: cut a surface by a plane or face and keep one side.
- thicken: offset planar and circular-cylindrical faces along their
normals (one side or symmetric) into a solid. Plane copies slide;
cylinder copies scale about the axis, exact for NURBS circles. Free
edges get ruled walls. Faces meeting at a sharp edge are refused.
Doc features Patch, Stitch, Thicken (with operations) and SurfaceTrim;
engine commands FusionSurfacePatchCommand, FusionSurfaceStitchCommand,
FusionSurfaceThickenCommand and FusionSurfaceTrimCommand.
Tests (volumes):
- A 10x10 patch thickened by 2 gives 200, also symmetric.
- Half a cylinder side thickened outward gives half a ring; both halves
inward give the full ring.
- Six faces of a box stitched back give 6000; an open box with its top
patched from the edges, stitched, gives 6000.
- Trim keeps 30 or 70 of 100.
- Engine: patch, trim, thicken gives 140.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01AS5Tn3xieewUSg3uxrMVdL
midasdf