A hole drilled along a panel, into its rim, has no place in the flat pattern
as a cut-out, so every such hole was refused. It is now kept as a bore of that
panel, in flat coordinates, and cut only from that panel's material when the
folded part and its flat pattern are built, so the sheet still unfolds and
folds back with it. A hole that would run into a bend, or cross a panel at an
angle, is still refused. The flat pattern lists the bores.
The action matrix worker takes ACTION_MATRIX_ONLY (just these actions) and
ACTION_MATRIX_UNFOLD (unfold and refold every sheet after each action) for
rechecking one group by hand.
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Name a side drawn on several sketch curves by all of them
An extrude named each side wall after the one sketch curve its profile
segment lies on. A wall along two coincident lines (squares drawn edge to
edge) or along collinear lines merged into one profile segment had no
single curve, so it was named from geometry and could not carry a sketch
attachment. One sketch extruded up and down and joined (the logo) refused
a sketch on every one of its side walls.
Such a side is now named by every curve it lies on, in sketch order: the
first is its name, the others aliases. The set is fixed by the sketch, so
the name is exact. The refusal message no longer blames merged faces.
Adds the reported logo design and a synthetic up-and-down join to the
action-matrix designs, and a regression test that sketches and extrudes on
every flat face, fresh and after save and reopen.
Fixes#954
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Action matrix: record the up-and-down join designs
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
Fillets and chamfers ending on a boss's pieced wall or beside it, on a face that runs along its seam twice, and loops the loop blend refuses
- A straight edge whose end meets one curved surface in several faces (a cylinder a join left
in pieces) ends on that surface: the section is cut where it crosses each seam, which is
shortened there; where no seam is crossed (the wall missing inside the other body) the
section lies on the bared surface and the rest of the side edge becomes a seam.
- Two end faces that aren't both planes meeting in lines: each face takes the section's points
on it, cut where it crosses the edge between them. Not where an end face runs on smoothly
from a side (an earlier round): the corner build takes those.
- Face boundaries close over several connector edges.
- A face on a periodic surface running along its seam twice (as a STEP file gives it) is
rebuilt the same way (#691).
- A curved chain ending square on a face that runs on past its side extends that face's seam.
- A smooth chain stops before an edge between faces that meet smoothly.
- A loop the loop blend refuses for its shape is blended edge by edge; refusals about its size
stand.
- Action matrix: ACTION_MATRIX_ACTIONS and ACTION_MATRIX_VALIDITY for quick local runs; the
fillets and chamfers that pass now recorded.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Loading a design (from a worker's start or restart to its first output) gets 300 s; each action keeps 90 s. oracle/41-tube-radial-holes (about 23 s here) timed out loading on a loaded CI runner, and reloads after a hung action were charged to the next action.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Sheet metal rims and bend ends attach by name (<panel>:rim.<edge>, <flange>:rim.bend0/1), as do face profiles from sheet faces. A plain or counterbored Hole square to a panel is machined into the flat pattern. Boss, Lip, Rest and Snap Fit keep the body's history and name their own faces. Hole tools name their faces by the part they cut, and pattern copies as copies. A pattern's repeated fillets keep the body's history. Loft sides are named by their section curves. A piece Offset Face moved off its face's plane attaches by its own qualified name. Sides of a profile grown to overlap a flush body keep their sketch line's name, so walls a Join merged take a sketch (#681). Face sketch 75% -> 90%, offset plane 75% -> 90%, press-pull/extrude 64% -> 85% in the action matrix; baseline blessed.
Fixes#494, fixes#495, fixes#560, fixes#561, fixes#563, fixes#564, fixes#681.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
The `pi` story of examples/demo/enclosure_ui_mcp.py keeps the 0.6 flow and adds the rim
rounded in one pick (a tangent chain), "Pi 4" engraved in the floor in DejaVu Sans Bold, and a
PETG material defined in the design, with its mass in Properties, before the height change.
The 0.6 story stays as `pi-0.6` (it built demo/pi-case). The center rectangle now comes from
the Rectangle drop-down. The finished case is in the action matrix corpus as
demo/pi-case-0.8.
docs/screenshots/demo-0.8.gif (9.3 MB) and demo-0.8.mp4 (9.9 MB) replace the 0.6 files: 41 s
at 9x playback.
Co-authored-by: Claude Opus 5.5 <[email protected]>
A flat face that no construction certificate names on its own now attaches by its exact history name (a new lineage face certificate): cut walls and floors, chamfer faces, each pattern or mirror copy, side walls a Join merged, and the pieces a later feature split a face into. Construction certificates still come first; a seed keeps its certificate when it is patterned. Two flush extrudes of one outline joined end to end keep their exact history in the prism boolean. Face sketch 52% -> 71%, offset plane 52% -> 71%, press-pull/extrude from face 41% -> 60% in the action matrix; baseline blessed.
Fixes#491, fixes#492, fixes#493, fixes#557.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
apps/solidcraft-cli/tests/action_matrix.rs tries sketch, offset/angle/mid planes, press pull, extrude from a face, hole, draft, shell, fillet, chamfer, axes, points, planes, projection, move, copy, mirror and pattern on the final bodies of 104 designs (the old design files, the examples, the 76 reference recipes, the enclosure demos, the Pi case built through the UI, eight typical parts), through the commands and picks the desktop sends, each design in its own process, with an edit round on a sample of passes. tests/action_matrix/baseline.json is a ratchet: an action that passed there and fails now fails the test; newly passing ones are reported for cargo xtask action-matrix --bless. Every CI run checks a fixed sample; the nightly Action matrix job runs the whole matrix in four parts. 30,567 of 35,576 actions pass (85.9%); results and causes in docs/action-matrix.md, one ignored reproduction per open cause (#556-#568).
Co-Authored-By: Claude Opus 5.5 <[email protected]>
