sheet.export_dxf writes an AutoCAD 2000 drawing with ELLIPSE and SPLINE entities for ellipses, splines and text outlines instead of chords, with curves: arcs for machines that read only lines and arcs. Perforation circles go through the same writer. Closes#1089.
Adds sheet.perforate: round holes on a staggered or square grid over the flat sheet, kept clear of edges, cut-outs and bend zones. The holes go to the flat pattern, the DXF and the measured volume rather than the B-rep, so a panel can carry many thousands of them.
A hole drilled along a panel, into its rim, has no place in the flat pattern
as a cut-out, so every such hole was refused. It is now kept as a bore of that
panel, in flat coordinates, and cut only from that panel's material when the
folded part and its flat pattern are built, so the sheet still unfolds and
folds back with it. A hole that would run into a bend, or cross a panel at an
angle, is still refused. The flat pattern lists the bores.
The action matrix worker takes ACTION_MATRIX_ONLY (just these actions) and
ACTION_MATRIX_UNFOLD (unfold and refold every sheet after each action) for
rechecking one group by hand.
Co-authored-by: Claude Opus 5.5 <[email protected]>
Convert to Sheet Metal now takes a solid or a shelled body by its bend edges (`bends`): the faces reached from the fixed face across those edges become the sheet, keeping the part's envelope, with the flat pattern by the rule's K-factor and radius. Other edges between sheet faces are cut open. The result works with edge flanges, cuts, Unfold/Refold, the flat pattern and DXF. A conversion without `bends` is the plate conversion as before. The optional `bends` field is noted under format 17. Fixes#647.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
The bend table, flat pattern and DXF list a bend only where its centre line has material: a bend that cut-outs (or pockets that together go through the sheet) shorten keeps what is left, and one they split gets a row per piece, all with the bend's number.
Co-authored-by: NOWN-DEV <[email protected]>
sheet.flat_pattern reports every cut-out exactly in a new cutout_shapes list, parallel to cutouts: a round hole as a circle, other cut-outs as their lines, arcs and (for other curves) polylines. Pockets get the same. The DXF writer and the JSON share one circle test. Un-ignores the #542 regression test. Fixes#542.
Co-authored-by: jonaswre <[email protected]>
sheet.flange refuses the sheet values its rule owns (thickness, K-factor, bend radius, reliefs, hem gap) instead of silently ignoring them, and says to use a rule. Un-ignores the #570 regression test. Fixes#570.
Co-authored-by: jonaswre <[email protected]>
A stored fold whose fixed point drifts off the sheet after a parameter change keeps the side the point lies on and shows a warning instead of breaking the timeline. A new fold still refuses a fixed point off the sheet, atomically. Un-ignores the #370 regression test. Fixes#370.
Co-authored-by: jonaswre <[email protected]>
Sheet Metal Rules get a Corner Relief Shape (notch, round or rectangular), sized by the rule's corner relief, cut where two bends meet at a corner of the base. Notch, the default, keeps existing designs as they were. File format 16.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
One edge flange feature gave all its flanges one height and one angle. A
part whose flanges lean differently took one feature per angle, and
flanges of separate features don't close toward each other, so its
corners stayed open.
- sheet.flange (edge): an entry of `edges` is a point [x, y, z] as before,
or {point, angle?, height?} whose angle and height (expressions, checked
like the feature's) replace the feature's for that edge. Bad input is
refused with the edge named. Before, the object form was read for its
point and the rest was ignored without a word.
- The feature stores its edges as FlangeEdge. An edge without values of
its own is written as the plain point it always was, so designs without
them are read and written as before; an unknown key in an edge is
refused, not dropped.
- The edges' values are feature inputs of their own (Edge angle, Edge
height, after the feature's), so parameters, renames and
parameters.change reach them. timeline.edit names the edges again when
it changes them, so each value stays with its edge.
- SheetBody::add_flanges_each trims every edge by its own setback and
adds the flanges. The corners between them close as between equal
flanges: the closing already works from the two flanges it joins (each
one's fold and leg), so the flat pattern follows by hand from the
angles, the heights and the rule (the tests derive it).
- The Flange dialog shows a row per picked edge with an angle and a
height box (empty: the dialog's value) once more than one edge is
picked, and brings them back on Edit Feature.
Co-authored-by: Claude Opus 5.5 <[email protected]>
Edge flanges meeting at a corner of the base were closed only at exactly
90°; at any other angle they stayed open (a V at 72°) and the rule's gap
was not used.
The flanges of one feature now close at any convex base corner and any
bend angle: each panel end is cut square to the sheet on a line in the
flat (slanted off 90°, stored as ext plus a new per-end slope) so the
edges nearest each other, on the inner faces, run parallel the rule's gap
apart about the plane bisecting the inner faces. The construction reads
the two flanges' own angles, so it holds for unequal ones as well. At 90°
it is the extension the old code gave (reference case 69-sm-tray is
unchanged). A corner that can't close (a gap under 0.01 mm, flanges
bending opposite ways, ends that would overlap in the flat pattern) stays
open, and the flange feature reports a warning that says where and why.
A flange of a later feature leaves the corner as it was (reference case
75-sm-bracket-holes: the earlier flange keeps its length).
Tested at 72° and 90° against a hand derivation, on a trapezoid, and
every 5° from 45° to 135° on a rectangle and a trapezoid (gap exact, one
flat region without hairline edges, one valid shell holding the flat
material).
Co-authored-by: Claude Opus 5.5 <[email protected]>
* feat(sketch): constructive solving ahead of the numeric solver
Part 1 of splitting #251: the sketch crate only. A graph-constructive front
end (Owen 1991; Fudos & Hoffmann 1997) places what it can by ruler-and-compass
loci and cluster decomposition, Levenberg-Marquardt finishes and verifies the
rest, and the rank analysis stays authoritative for degrees of freedom. Solves
can follow a reference (the previous solution), so edits and drags keep their
branch instead of flipping.
New API: solve_with (hold, reference, analysis, budget) and
solve_after_value_edit; solve and solve_holding keep their signatures as
wrappers, so no caller changes here.
When the seed moves an arc's centre, the arc's unconstructed ends start carried
along (the arc translates) instead of left behind for LM to turn; found by the
reference test 20-slot-constrained.
Refs #203
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01TWc1smHYwTSVrVc8SNvS44
* feat(doc): keep a sketch's solved state across value edits
Part 2 of splitting #251 (builds on part 1, the sketch crate):
- Sketch edits solve for the document's values continuing from the stored
solved state (Document::solve_sketch), so a dimension edit keeps the
sketch's branch instead of re-solving from scratch.
- A value edit (parameters, a configuration, the units) that would make a
sketch that solved before fail or turn over is refused with the
conflicting constraints named; otherwise the solved sketches are written
back into the document (Model::adopt_solved_sketches), which changes what
saved designs store.
- Later features are keyed by a sketch's solved geometry (to a 1e-6 mm
quantum), so setting a value back reuses their earlier results.
- Solved sketches in a model state are shared (Arc) between states.
Refs #203
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01TWc1smHYwTSVrVc8SNvS44
* feat(sketch): live drag that keeps its solution, ended by sketch.drag_end
Part 3 of splitting #251 (builds on part 2):
- sketch.drag follows a long move in short held steps, so the geometry keeps
its branch, and reports how far it got (reached, at).
- live: true runs one frame of an interactive drag: the sketch is solved
once and shown, later features keep their last result (marked stale)
until sketch.drag_end or any command that reads the model evaluates it
(CommandSpec::live, reads_model, doc_only).
- sketch.drag_end adds the constraint the drag let go on and evaluates the
model once.
- Undo and redo evaluate a new document once (execute does) instead of
twice.
- The viewport drives drags through live frames and drag_end; dimension
text drags start only off sketch geometry.
Refs #203
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01TWc1smHYwTSVrVc8SNvS44
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
sheet.flange now lists name?/body_name?, solid.loft and solid.sweep list
targets?/name?/body_name?, and the primitives list name?/body_name? (all go
through add_feature, which reads them). A test pins the shared keys for
every body-creating feature.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
Record ownership transfers in the timeline so earlier Join/Cut membership,
world placement, machining data and styles survive component moves, edits,
independent copying, undo and reopening. Preserve pending positions in history
snapshots and keep constructor transfers ordered during feature redefinition.
Retain shallow sheet pockets and exact planar intersection islands through
unfold/refold, with depth-aware flat previews and DXF export. Store explicit
3D wire coordinate spaces and migrate known legacy provenance without moving
saved points or analytic fits.
Infer unique eligible cylindrical Emboss targets, align Revolve manipulators
with actual extent geometry, and discard obsolete preview errors after input
correction. Certify constructed and immutable imported face styles using exact
source metadata while preserving legacy face names. Upgrade designs to format10
with bounded validation and geometry-preserving legacy migration.
Persist typed sketch dimensions and bounded ordered configuration rules in format 8. Use exact occurrence paths and source identity for editing, movement, appearance, and mass. Preserve sheet material regions through cutting, folding, and exact DXF export; retain nested cavities and material islands.
Validation: cargo xtask ci passed, including 368 engine tests, 178 UI tests, 68 UI scenarios, 136 kernel tests, and the 10-crate wasm check. Actual preview workflows and legacy format-7 origin-corner reopening were inspected.
The old ids live only in crates/engine/src/legacy_ids.rs (the legacy migration table): find_command maps them, so old scripts, recipes and control calls keep working, and saved shortcuts, recent and pinned commands are migrated on load (designs store no command ids). Parity maps the observed catalog ids to ours through xtask/data/fusion-ids.tsv. The agent rule now reads: our own dotted id, never another product's. Cargo.toml's repository points at github.com/bherbruck/solvecraft.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
- solvecraft_io::vfs: the engine's file access (disk natively; in the browser an in-memory set of
files the host loads and stores). File commands and write_atomic go through it.
- Web host (apps/solvecraft-web/src/files.rs): stored designs are read from OPFS at start
(storage.persist() asked for) and written back when a command writes one; Save/Save As keep
designs in the browser, exports (STEP, STL, 3MF, OBJ, ...) download as files.
- File > Open shows "Files in this browser": open, insert, rename, download, delete, plus open or
insert from the computer (showOpenFilePicker where there is one, an <input type=file>
otherwise). Files dropped on the page are inserted or opened.
- Unsaved work is autosaved to OPFS and offered again after a reload or crash.
- Start page recents come from the stored designs, with thumbnails. In the browser the samples
are built when opened (a picture blocks the page there, and a kernel panic can't be caught).
- Pages without OPFS (http on a network address, old browsers) keep designs in local storage.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01AS5Tn3xieewUSg3uxrMVdL
ASSEMBLE panel (SOLID, SHEET METAL, PLASTIC): New Component, Joint, As-built Joint, Joint Origin,
Rigid Group, Drive Joints, Motion Link, Interference. Joint origins are picked by hovering:
faces snap to their centre (round faces to the centre of the nearer end), edges to their middle
(round edges to their centre), vertices to themselves, shown as glyphs with their z axis. The
Joint dialog has the motion type, angle, offsets X/Y/Z, flip, per-value limits and Animate (the
preview plays the motion); joints and drives preview on the placed model (world states).
Drive Joints moves live with a slider. Interference lists the overlaps and shows them red.
Joints appear in the timeline and in a Browser Joints folder (edit, drive, suppress, delete).
SHEET METAL tab in Fusion's layout: Flange (base, edge or contour, from the picks; height arrow
on the canvas), Hem, Unfold, Refold, Convert to Sheet Metal, Sheet Metal Rules (rule manager),
Create Flat Pattern (flat view with up/down bend lines, bend table, DXF export).
PLASTIC tab with SETUP: Boss, Lip/Groove, Snap Fit, Rest, Manage and Assign Plastic Rules; Rib,
Web and the shared solid commands on the tab.
Every feature dialog has live preview, Edit Feature and pre-selection; icons drawn in code.
Toolbar layout per tab in workspace.rs; tests for the dialog to command mapping.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01AS5Tn3xieewUSg3uxrMVdL
NOWN-DEV