On a large thin sheet the probes around the fixed point stepped clean through
the sheet (twice the mesh tolerance of a 465 mm part is more than its 0.8 mm
thickness), so a point exactly on the face touched no material and the fold
was refused. The probes now also step a quarter of the thickness.
Co-authored-by: jonaswre <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Rounded Rectangle sketch tool (#891)
A new SKETCH > CREATE command, sketch.rectangle.rounded, in the Rectangle
family: two opposite corners and a corner radius make a 2-point rectangle
whose four corners are filleted alike, as one undo step. The radius is one
parameter (one radius dimension, the other arcs equal to it), so changing it
changes all four corners. While drawing, Width, Height and Radius boxes take
typed values; typed width and height dimension the overall size between
opposite sides. Without a typed radius the corners get a fifth of the shorter
side.
Fixes#891
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Rounded Rectangle in the Simplified Chinese catalog
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
Session::replace_design keeps auto_project when file.new, doc.open and doc.recover swap in another design, and the UI keeps it across tabs, adopt and the last-tab close. Regression tests in engine (sketch_project) and ui-egui (documents).
Offsets picked faces along their normals into a new surface body: planes and cylinders move exactly, other faces get a fitted B-spline within tolerance, and offsets that would fold over are refused. Adds the SurfaceOffset feature (noted under format 18), the surface.offset engine command and an Offset Surface dialog.
Closes#758.
Co-authored-by: jyviko <[email protected]>
A design with components and joints exports as a URDF robot description (file.export to .urdf, the MCP export tool, solidcraft-cli run --out, File > Export URDF...). It writes one binary STL per component in metres, links with mass, centre of mass and inertia from material density, and maps rigid, revolute, slider, cylindrical, pin-slot, planar and ball joints to URDF joints or short chains. Loops, broken joints and loose parts are reported as warnings. Options: mesh_prefix, effort, velocity. Docs in docs/urdf.md.
Each wall of a surface built from sketch curves (Surface Extrude, Revolve, Sweep and Loft) is now named after the curve it comes from, exactly rather than from geometry, so references to those faces survive edits.
Surface Loft lofts open or closed curve chains, one section per sketch in pick order, into surface bodies. Adds the SurfaceLoft feature (format 18 note), the surface.loft command, a dialog with Edit Feature support, and kernel and engine tests.
Part of #757.
Surface Sweep carries open curves and closed profile boundaries along a sketch path into surface bodies, with smooth walls along curved point paths. Adds the SurfaceSweep feature (format 18 note), the surface.sweep command, a dialog with Edit Feature support, and kernel and engine tests.
Part of #757.
Surface Revolve turns open curves and closed profile boundaries about a sketch axis into surface bodies, with cone apexes and sphere poles where a chain ends on the axis, and a closed shell made solid. Adds the SurfaceRevolve feature (format 18 note), the surface.revolve command, a dialog with Edit Feature support and analytic kernel and engine tests.
Part of #757.
A lip picked on a face that isn't a shelled body's rim, such as the Sample Plate's top
face with its two holes and the boss standing on it, ran its band round the largest inner
edge. That was the boss's foot, so the band stood against the boss's wall and the join
failed with a boolean error about curved faces.
The band now goes round the face's opening (an inner edge with no material just over the
face inside it). A rim face that has a smaller hole in it still works. A face whose inner
edges are only where other features stand on it, or whose openings are alike in size (a
plate's holes), is refused with a plain message that names the rim face it needs.
Fixes#892.
Co-authored-by: Claude Opus 5.5 <[email protected]>
Hole centres from a sketch now drill into the material on whichever side of the sketch plane it lies: material the spot starts in wins, then the nearest body ahead, else against the sketch normal as before. A sketch on a part's underside or below it now drills up into the part. Covers counterbores, through-all, edge and corner centres, patterns and reopening.
Delete Face takes heal (default true, as before). With heal: false the picked faces are removed and the gap stays open, leaving the remaining faces as a surface body (kernel remove_faces); deleting every face is refused. Saved only when false, noted under format 18.
Display meshes after opening, the face names read when a feature finds a face by name, and inspect.measure over all bodies are now worked out per body on plain scoped threads (solidcraft_kernel::for_each_on_threads / map_on_threads), in body order and with the same results; the browser build stays serial.
A sketch text gets an optional style: bold and italic faces (a slanted fallback for italic), left/center/right alignment, letter and line spacing, and a path curve of the same sketch for the baseline to follow (reverse takes the other side). Edit Text gets B/I toggles, alignment, spacing fields and a Path chip, all live. The style is saved only when not plain and is noted under format 18.
Renaming a body used to replace every string in later features equal to its old name, including sketch text, plane and feature names and expressions. Now only values under keys that name bodies (body, bodies, target, targets, tools) at any depth are rewritten, with a test that a sketch text spelling the body's name stays while a move follows the rename.
A hole drilled square to a flange's panel, not only the base's, is now a flat cut-out of the sheet: it unfolds with its panel to where the bend allowance puts it, shows in the flat pattern and DXF as a circle, and survives unfold and refold. A pocket tool spans the cut-outs already inside it (a counterbore's hole), so the order they are made in no longer matters. Fixes#560.
When an extrude cuts with profiles whose outlines stay more than 1 µm apart (the letters of a text), their tools are apart too, so they are joined and cut from the body in one boolean instead of one per profile. A ten-letter text cut drops from about 13 s to 1.5 s with the same result. Sheet metal targets and touching profiles keep cutting tool by tool. Tapered extrudes are unaffected.
Agent tool calls (MCP, and bridged control requests carrying allow_paths) reach files only in the open design's folder (strictly inside home or the temporary folder, not in a hidden folder, and never its hidden files), the app's recovery folder, the server's private scratch folder and each --allow-path; --allow-any-path lifts the limit. Paths are resolved first, so .. and symlinks that lead out (including a save through a link, #845) are refused. On Windows, UNC, device, NT, verbatim non-drive, drive-relative, alternate-stream, reserved-device and 8.3 short-name paths are refused before any file system call, and the resolved path must be on a local drive. doc.recovery_discard and doc.recover {discard} delete only real recovery entries. Docs: mcp.md, control-protocol.md, README.
A Sketch Palette toggle (sketch.options show_construction) that hides construction geometry from drawing and picking; saved with the sketch's view options under format 17.
Co-authored-by: William Dunn <[email protected]>
surface.extrude sweeps open curve chains and profile boundaries along the sketch normal into a surface body (walls only, no caps). Saved under format 17.
Refs #757
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Icons for the surface toolset, and its planned commands registered and disabled with the issue that tracks each one.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Sketch Move gets a toolbar placement in Sketch > Modify and a Move/Copy tool window with X and Y distances, an angle, an optional centre point and a Create Copy flag, replacing the context-menu route that ran the command with no parameters.
The feature history can sit in a panel on the left, with folders that hold one unbroken run of features, drag and drop as one undo step, and a resizable divider. Timeline folders save under format 17.
A sketch's link to a projected edge now keeps the edge's persistent name and finds it by that name when the body changes, instead of taking whichever edge ends up nearest its point.
Adds `fit: taper` to Fillet: where a constant radius doesn't fit along a straight edge, it follows the room there as a smooth spline, down to zero where a face closes to a point. Taper to Fit is in the Fillet dialog, and the feature's warning says how far it tapered.
`SolveApp::start` now honours a command's enabled flag, so shortcuts, the command palette and the control channel can't start a disabled command, and Move is disabled while a sketch is open.
Convert to Sheet Metal now takes a solid or a shelled body by its bend edges (`bends`): the faces reached from the fixed face across those edges become the sheet, keeping the part's envelope, with the flat pattern by the rule's K-factor and radius. Other edges between sheet faces are cut open. The result works with edge flanges, cuts, Unfold/Refold, the flat pattern and DXF. A conversion without `bends` is the plate conversion as before. The optional `bends` field is noted under format 17. Fixes#647.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Extrude and Revolve from a body face take `face_body` to say whose face is meant where faces of several bodies meet flush at the picked point. Without it, an ambiguous pick now names the bodies that meet there instead of saying there is no face. Fixes#703.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Dragging a text outline now moves the whole editable text, and Move/Copy shifts or rotates it as one piece (a copy stays independently editable). Content, font, height and outline identities are kept; a drag is one undo step and Esc restores the start.
Sheet-metal cut-outs and base flange outlines drawn with ellipses, splines or text stay exact curves in the flat pattern and the unfolded body; the folded body follows them with tangent arcs within 0.001 mm (#659).
Adds render.backends, a metadata-only command that lists the render backends, their executors and profiles, with strict request resolution in the render crate (docs/render-backends.md).
A clover of same-size rectangles drawn around a shared corner was refused as over-constrained.
Constraints that remove no degree of freedom but still hold (zero residual) are now kept and shown dimmed as redundant. Conflicting ones are still refused. A redundant driving dimension is refused with "already determined by ...". Typed sizes become driven (reference) dimensions. Drawing no longer adds Horizontal/Vertical to a side that is already implied through two coincident corners. The solver reports redundant constraints using a Jacobian row-dependence test.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
An edge flange picked on an edge that cut-outs have partly removed is built along what is left of that edge (the stretch nearest the pick), so each side of a notch can get its own flange.
0.8.0 shipped format 16. Lineage names of a piece qualified by the faces around it, and sheet face names of a rim (rim.<edge>) or a bend end (rim.bend0/1), now come under format 17. Format 16 designs need no transformation, and the version stamp makes 0.8.0 ask for an update.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
