bherbruckandClaude Opus 5.5
296683229d
* WIP deep rename (not for push) * WIP2 * WIP3 * WIP4 wxs fix * rustfmt * Rename the remaining identifiers in merged crash-report code Co-Authored-By: Claude Opus 5.5 <[email protected]> Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT --------- Co-authored-by: Claude Opus 5.5 <[email protected]>
111 lines
1.4 KiB
JSON
111 lines
1.4 KiB
JSON
{
|
|
"commands": [
|
|
{
|
|
"command": "sketch.create",
|
|
"params": {
|
|
"plane": "XY",
|
|
"name": "Base"
|
|
}
|
|
},
|
|
{
|
|
"command": "sketch.rectangle.two_point",
|
|
"params": {
|
|
"p0": [
|
|
0,
|
|
0
|
|
],
|
|
"p1": [
|
|
40,
|
|
30
|
|
]
|
|
}
|
|
},
|
|
{
|
|
"command": "sketch.finish",
|
|
"params": {}
|
|
},
|
|
{
|
|
"command": "solid.extrude",
|
|
"params": {
|
|
"distance": 10,
|
|
"name": "Block"
|
|
}
|
|
},
|
|
{
|
|
"command": "sketch.create",
|
|
"params": {
|
|
"plane": "XY",
|
|
"name": "SlotSketch"
|
|
}
|
|
},
|
|
{
|
|
"command": "sketch.rectangle.two_point",
|
|
"params": {
|
|
"p0": [
|
|
15,
|
|
-5
|
|
],
|
|
"p1": [
|
|
25,
|
|
35
|
|
]
|
|
}
|
|
},
|
|
{
|
|
"command": "sketch.finish",
|
|
"params": {}
|
|
},
|
|
{
|
|
"command": "solid.extrude",
|
|
"params": {
|
|
"sketch": "SlotSketch",
|
|
"distance": 10,
|
|
"start_offset": 5,
|
|
"operation": "cut",
|
|
"name": "Slot"
|
|
}
|
|
},
|
|
{
|
|
"command": "solid.fillet",
|
|
"params": {
|
|
"edges": [
|
|
[
|
|
40,
|
|
15,
|
|
10
|
|
]
|
|
],
|
|
"radius": 2,
|
|
"name": "Round"
|
|
}
|
|
},
|
|
{
|
|
"command": "solid.chamfer",
|
|
"params": {
|
|
"edges": [
|
|
[
|
|
0,
|
|
15,
|
|
10
|
|
]
|
|
],
|
|
"distance": 1.5,
|
|
"name": "Bevel"
|
|
}
|
|
},
|
|
{
|
|
"command": "solid.offset_face",
|
|
"params": {
|
|
"faces": [
|
|
[
|
|
7,
|
|
15,
|
|
10
|
|
]
|
|
],
|
|
"distance": 2,
|
|
"name": "Raise"
|
|
}
|
|
}
|
|
]
|
|
} |