N3MI-DGandClaude Opus 5.5 ff1453f868 View cube face labels are larger: one font size for all six, the widest (BOTTOM) spanning 90% of its face, instead of a fixed 9.5 px that left the names small on the cube. Tests: BOTTOM spans 90% of the face seen straight on, and every label stays within its face from any direction ...

Co-Authored-By: Claude Opus 5.5 <[email protected]>

2026-10-11 10:06:05 +11:00

..

doc

solid.cylinder, box, sphere, torus and coil place by expressions: base, corner and center take numbers or length expressions per coordinate ("basin_width/2", "10 mm") and follow parameter changes, renames and component frames; before, a point that was not three plain numbers (or an unreadable axis) was silently replaced by the origin (or Z). The features now store the point as expressions (plain numbers still saved as numbers, so existing designs read and write the same) and evaluate it on every recompute; an unreadable or out-of-range point or axis is refused with an error. Tests: primitive points take expressions, follow parameters, renames and a moved component, and bad points are refused

2026-10-10 18:37:22 -04:00

engine

Merge pull request #97 from CypherNaught-0x/fix/dimension-measured-after-solve

2026-10-10 18:49:25 -04:00

geom

fix: select complete circular rims and curved surfaces in 3D

2026-10-10 17:13:36 -04:00

io

solid.cylinder, box, sphere, torus and coil place by expressions: base, corner and center take numbers or length expressions per coordinate ("basin_width/2", "10 mm") and follow parameter changes, renames and component frames; before, a point that was not three plain numbers (or an unreadable axis) was silently replaced by the origin (or Z). The features now store the point as expressions (plain numbers still saved as numbers, so existing designs read and write the same) and evaluate it on every recompute; an unreadable or out-of-range point or axis is refused with an error. Tests: primitive points take expressions, follow parameters, renames and a moved component, and bad points are refused

2026-10-10 18:37:22 -04:00

kernel

A sweep along a path with sharp corners follows the corners: sweeping a rim profile along three lines (an open rectangle) gave a body of volume -0.0006 mm3 with its centre of mass at x = -3.5e9, and no error

2026-10-10 17:57:34 -04:00

mcp

A failed MCP batch goes back to where it started however long the undo history is: rollback undid as many steps as the undo history had grown, but the history is capped at 200 steps, so once it was full a failed batch reported undone: 0 and left its sketches behind (an empty Sketch1, two sketches named TapHole). New commands edit.checkpoint and edit.restore_checkpoint (forget: true drops one) remember and restore the design, the active sketch and the undo history; batch takes a checkpoint before its first step, restores it on a failure and forgets it on success. Against an app without checkpoints batch falls back to counting undo steps

2026-10-10 17:21:25 -04:00

render

Section Analysis: cut faces in their body's colour (tinted toward the cap colour) and hatched; snapshots show the section too (the cut part removed, hatched cut faces)

2026-10-10 17:05:23 +00:00

sketch

Merge origin/main (with #86): sketch.dimension reports the solved value in the dimension's unit; the spout test expects the solved 30 and 60 degrees

2026-10-11 00:13:51 +02:00

ui-egui

View cube face labels are larger: one font size for all six, the widest (BOTTOM) spanning 90% of its face, instead of a fixed 9.5 px that left the names small on the cube. Tests: BOTTOM spans 90% of the face seen straight on, and every label stays within its face from any direction

2026-10-11 10:06:05 +11:00