fix(polar): only snap near a polar ray (#70)

POLAR locked the cursor to the nearest angle everywhere, so it could
never point between angles. Snap only when the cursor is within the snap
aperture (in screen pixels) of a polar ray; otherwise leave it free, so
POLAR behaves as if off when pointing away from every angle. The polar
guide line now shows only while actually snapped.

Co-Authored-By: Claude Opus 4.8 <[email protected]>

src/app/helpers.rs

@@ -150,6 +150,34 @@ pub(super) fn polar_constrain(pt: glam::Vec3, base: glam::Vec3, step_deg: f32) -
     )
 }
 
+/// Polar constraint that only engages when the cursor is within `tol_px`
+/// screen pixels of the nearest polar ray; otherwise the cursor is left free
+/// so POLAR behaves as if off when pointing away from every angle (issue #70).
+pub(super) fn polar_constrain_near(
+    pt: glam::Vec3,
+    base: glam::Vec3,
+    step_deg: f32,
+    view_proj: glam::Mat4,
+    bounds: iced::Rectangle,
+    tol_px: f32,
+) -> glam::Vec3 {
+    let snapped = polar_constrain(pt, base, step_deg);
+    let to_screen = |w: glam::Vec3| {
+        let ndc = view_proj.project_point3(w);
+        (
+            (ndc.x + 1.0) * 0.5 * bounds.width,
+            (1.0 - ndc.y) * 0.5 * bounds.height,
+        )
+    };
+    let (cx, cy) = to_screen(pt);
+    let (sx, sy) = to_screen(snapped);
+    if ((cx - sx).powi(2) + (cy - sy).powi(2)).sqrt() <= tol_px {
+        snapped
+    } else {
+        pt
+    }
+}
+
 // ── Clipboard / selection helpers ──────────────────────────────────────────
 
 /// Compute the centroid of a set of wire models (average of all points).

src/app/update.rs

@@ -1,5 +1,5 @@
 use super::helpers::{
-    ortho_constrain, parse_coord, polar_constrain, ucs_rotate_vec, ucs_to_wcs, ucs_z_axis,
+    ortho_constrain, parse_coord, polar_constrain_near, ucs_rotate_vec, ucs_to_wcs, ucs_z_axis,
     CoordKind,
 };
 use super::{Message, OpenCADStudio, POLY_START_DELAY_MS};
@@ -2253,7 +2253,14 @@ impl OpenCADStudio {
                         if self.ortho_mode {
                             snapped = ortho_constrain(snapped, base);
                         } else if self.polar_mode {
-                            snapped = polar_constrain(snapped, base, self.polar_increment_deg);
+                            snapped = polar_constrain_near(
+                                snapped,
+                                base,
+                                self.polar_increment_deg,
+                                vp_mat,
+                                bounds,
+                                self.snapper.snap_radius_px,
+                            );
                         }
                     }
 
@@ -2440,7 +2447,14 @@ impl OpenCADStudio {
                                 if self.ortho_mode {
                                     pt = ortho_constrain(pt, base);
                                 } else if self.polar_mode {
-                                    pt = polar_constrain(pt, base, self.polar_increment_deg);
+                                    pt = polar_constrain_near(
+                                        pt,
+                                        base,
+                                        self.polar_increment_deg,
+                                        view_proj,
+                                        bounds,
+                                        self.snapper.snap_radius_px,
+                                    );
                                 }
                             }
                             pt
@@ -2484,7 +2498,14 @@ impl OpenCADStudio {
                         if let Some(base) = self.last_point {
                             let dx = effective.x - base.x;
                             let dy = effective.y - base.y;
-                            if (dx * dx + dy * dy).sqrt() > 1e-4 {
+                            // Only show the guide while POLAR is actually engaged
+                            // — i.e. the point is snapped onto a polar ray, not
+                            // floating free near no angle (issue #70).
+                            let step = self.polar_increment_deg.to_radians();
+                            let angle = dy.atan2(dx);
+                            let snapped = step > 1e-6
+                                && ((angle / step).round() * step - angle).abs() < 1e-3;
+                            if snapped && (dx * dx + dy * dy).sqrt() > 1e-4 {
                                 let far = 1e5_f32;
                                 let dir = glam::Vec3::new(dx, dy, 0.0).normalize();
                                 let far_pos = base + dir * far;
@@ -2911,7 +2932,14 @@ impl OpenCADStudio {
                             if self.ortho_mode {
                                 pt = ortho_constrain(pt, base);
                             } else if self.polar_mode {
-                                pt = polar_constrain(pt, base, self.polar_increment_deg);
+                                pt = polar_constrain_near(
+                                    pt,
+                                    base,
+                                    self.polar_increment_deg,
+                                    vp_mat,
+                                    bounds,
+                                    self.snapper.snap_radius_px,
+                                );
                             }
                         }
                         pt