Commit Graph
8 Commits
Author SHA1 Message Date
jyvikoandClaude Opus 5.5 417c0c8897 mesh: the tet objective sees needles; no tet below scaled Jacobian 0.3 on the skill's tet parts
The improvement objective was the smallest dihedral sine, which misses
needles: every dihedral angle fine while a corner is nearly flat, so
the corpus meshes had scaled Jacobians down to 0.01-0.07. The objective
is now the smaller of the dihedral sine and the scaled Jacobian at the
worst corner (the measure analysts check, Knupp 2001), weighted so a
Jacobian of 0.3 (the skill's limit) counts as a 30 degree dihedral
angle (the schedule's target): the Jacobian decides only near that
limit. The existing edge removal, multi-face removal, smoothing and
insertion then remove the needles.

Skill tet10 min SJ: sphere-on-plate 0.092 -> 0.335, filleted-bracket
0.021 -> 0.318 (both pass, nothing marked). Default-size tet10:
thin-ribs 0.240, shallow-groove 0.321, rounded-box 0.311.

The strong-relaxation test relaxes below 0.45: nothing is left below
0.3. Literature note in docs/meshing/literature.md.

Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
2026-10-17 00:51:20 -04:00
jyvikoandClaude Opus 5.5 a2a4f8895e mesh: strong relax keeps a morph unless it inverts, default reach five element lengths
Owner's rule (#438): move the bad nodes, interpolate, keep the morph as long as no
element inverts (guards "valid", the default); the old guards stay as "strict". The
run keeps its best round (highest smallest scaled Jacobian, then fewest elements below
the threshold, then highest mean) and never ends below the start. Default reach five
mean edge lengths of the bad elements (was three); on the Pi 5 base reach 3, 5 and 7
end at the same quality, 5 moving fewer nodes than 7 while leaving none below 0.7.

Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
2026-10-16 20:41:27 -04:00
jyvikoandClaude Opus 5.5 2456912850 mesh: strong relax objective never ranks an inverted element below a valid one
In the max-min phase a valid element's term q^-16 reached 1e96 as q -> 0+, far above
an invalid element's 2e8, so the descent kept elements inverted rather than pass
through flat: the distorted plate stayed tangled (4 invalid) once its mesh was the
same on every platform. The shape term now continues as its tangent line below
q = 0.3 (finite, steep) and an invalid element costs 1e11, above any valid one.

Adds a test that the plate's mesh, its perturbation and the strong relaxation are
the same bits with 1 and 4 threads and match a fingerprint taken on macOS (CI checks
it on Linux).

Part of #438.

Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
2026-10-16 18:30:00 -04:00
jyvikoandClaude Opus 5.5 4908f5679c mesh: strong relaxation morphs round the bad elements (harmonic interpolation within a reach)
The owner's direction: bad nodes move to better places, the nodes within a reach follow by
the graph Laplacian's harmonic extension, edges held, nothing outside the reach moves.
mesh.node.relax strong mode takes below and reach and reports each round.

Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
2026-10-16 14:55:59 -04:00
jyvikoandClaude Opus 5.5 6f94346253 mesh: mesh.node.relax mode strong, below and layers; partitioned bodies count as their cells
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
2026-10-16 14:55:59 -04:00
jyvikoandClaude Opus 5.5 b74d15e44d mesh: relax by face names the listed faces with no mesh (#471)
Faces no element is tagged with are left out and named in the reply
(faces_without_mesh); none tagged is the error.

Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
2026-10-16 09:21:21 -04:00
jyvikoandClaude Opus 5.5 3ee622f62a mesh: relax nodes by CAD face; params docs match their forms (#471)
mesh.node.relax takes faces: [{body, face}] (every node on those B-rep
faces and the nodes of the elements touching them, sliding on the faces)
and elements in its form; the undocumented-by-form set is dropped.
A schema test checks every top-level key a params doc names is accepted,
which also found mesh.hex.extrude normal, mesh.hex.project max_arc_angle
and mesh.plan.apply name missing from their forms.

Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
2026-10-16 09:21:21 -04:00
jyvikoandClaude Opus 5.5 94fdbf0fca engine, ui: mesh.node.relax and relaxation fields, Relax Nodes tool with sphere and preview (#398)
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01UhhZMBTviDQxZvwnyP89fo
2026-10-15 14:40:00 -04:00