Adds the read-only material.properties.validate command: schema_version 1 engineering material cards in SI units are checked for numerical consistency and elastic stability, with derived isotropic moduli, missing conditions and sources needing review. Nothing is assigned or saved.
Thanks @0xlillith.
Fixes#971. At the node limit the offset certificate splits the fitted curve where it meets the exact offset midpoint, so curves with different parameter speeds certify within the same 0.002 mm tolerance. Associated offset fit nodes are hidden from display, picking, box selection and snapping until Break Association.
Thanks @Karl-VonRichter.
Fixes#928. Extrude To / From Object and Revolve To Object now resolve their target in the feature's own component frame, so a face in another component whose occurrence is moved is found where it is shown instead of the extrude stopping at a flat plane through the picked point. The point is named after the nearest face, a named point keeps its named face when another component touches it there, and such features re-evaluate when a placement changes, so they follow the target when it moves later.
Co-authored-by: SychPL <[email protected]>
Fillet gets a Curvature (G2) radius type (type: "curvature", alias "g2"): a quintic blend whose size is the equivalent circular setback, for convex and concave straight edges between planar faces with a perpendicular planar end face at each end. Unsupported cases are refused rather than falling back to a circular fillet, and a blend that would cross a loop in its end face is refused. Persisted as a fillet style under format 19; labels in en/de/ja/ko/zh.
Co-authored-by: midasdf <[email protected]>
Trimming the base at an edge flange's setback snaps corners within tolerance onto the trim line and merges away the zero-width run a ledge as tall as the setback left along it, so the ledge goes with the strip as a lower one does. Splitting outline edges at other cells' corners now skips points within the model's tolerance of an end, so a ledge a little taller keeps its sliver and the bend runs under it, also off the axes. Both used to fail with "sew: a degenerate edge". Nothing new is stored.
A hole drilled along a panel, into its rim, has no place in the flat pattern
as a cut-out, so every such hole was refused. It is now kept as a bore of that
panel, in flat coordinates, and cut only from that panel's material when the
folded part and its flat pattern are built, so the sheet still unfolds and
folds back with it. A hole that would run into a bend, or cross a panel at an
angle, is still refused. The flat pattern lists the bores.
The action matrix worker takes ACTION_MATRIX_ONLY (just these actions) and
ACTION_MATRIX_UNFOLD (unfold and refold every sheet after each action) for
rechecking one group by hand.
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Holes on round faces from the app, one hole per pick, and Flip for holes at sketch points (#967)
The Hole dialog takes any face: a hole on a round face drills against the face's normal where it
was picked, and its arrow shows that. A round face split at its seam is picked whole, but makes
one hole where it was clicked. Holes at sketch points get Flip (saved as flip in the hole's points,
under format 18), in the command and in the dialog.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Holes at sketch points show their arrow: into the part, or away with Flip (#967)
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
Sketch Mirror, rectangular and circular Pattern, and Offset now show a green live preview that follows the selection and settings; OK commits, Cancel leaves the sketch unchanged. The shared dialogs show the current selection step and source counts, sources can be toggled with Ctrl/Cmd-click, cleared and reselected.
Offsets keep editable driving distance dimensions (One Side, Two Sides, Symmetric) that update the derived curves without moving the source, with undo/redo and save/reopen. Format 19: older files keep their fixed offsets.
New dialog labels in en, zh, ja, de and ko.
Fixes#696. Fixes#517.
The plate check compared the face outline's area (from the tessellation, so each hole was a polygon of chords) with the exact volume, and refused plates with a few small holes. Where the outline runs along a cylinder about the plate's normal it is now an arc of that circle; coaxial pieces of one radius are one wall, so a hole split into two, three or four faces is one circle. The check passes with its tolerance unchanged, and the flat pattern and its DXF carry one CIRCLE per hole (ARC for rounded corners and slot ends).
A round blank now converts too, so unfold_cut_refold_and_convert checks the refusal with a block thicker at one end instead of a rod.
* Hole matrix: placement, types, extents, edits and 0.9.0 designs, with today's failures listed
Each case checks the drill goes into the material, the bore sits on its axis, a blind hole stops
where it should, the removed volume against its analytic value, the face count and that every
body is still one closed valid solid. Failing cases are listed in tests/hole_matrix/known_failures.txt
as a ratchet.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* A hole on a face drills into the material, also in older designs (#950)
Without a direction, solid.hole took the direction from any face whose infinite plane passed
within ten tolerances of the point, the last one found winning: the far side of a thin plate or a
face of another body at the same height could set it, and the wrong direction was saved. It now
uses the face nearest the point, against its outward normal (exact for planes, cylinders and
spheres, so holes on curved faces work without a direction). When a design is evaluated, a face
hole whose saved direction leaves the face it starts on is mirrored into it, so designs saved
with the wrong direction drill into the part.
Fixes#950.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Hole at a point on no face (a planar face's centroid outside it) keeps the plane it lies in
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Record the hole direction fix in the goldens and the action matrix baseline (#950)
Seeds 7, 21, 81 and 85 drill their holes straight into their faces now. In the action matrix,
holes on four faces that used to go the wrong way now build, and two whose correct direction
meets a cut the kernel refuses are marked failing.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Goldens: seeds 7, 21 and 85 drill their holes straight in (#950)
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
- A fold's zone clipped across the root of a tab folded before on the same
line kept a sliver of no width there, which made the zone look like it
crossed a slanted edge. The one real piece is the zone now (#638).
- When the tabs a fold line spans can't take the side beyond them along,
because it joins the side that stays through other material (a tab on the
inside edge of an L, the fixed point on the far leg), the tabs' own ends fold
instead, the same part as with the fixed point on the near leg (#639).
Co-authored-by: jonaswre <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Name a side drawn on several sketch curves by all of them
An extrude named each side wall after the one sketch curve its profile
segment lies on. A wall along two coincident lines (squares drawn edge to
edge) or along collinear lines merged into one profile segment had no
single curve, so it was named from geometry and could not carry a sketch
attachment. One sketch extruded up and down and joined (the logo) refused
a sketch on every one of its side walls.
Such a side is now named by every curve it lies on, in sketch order: the
first is its name, the others aliases. The set is fixed by the sketch, so
the name is exact. The refusal message no longer blames merged faces.
Adds the reported logo design and a synthetic up-and-down join to the
action-matrix designs, and a regression test that sketches and extrudes on
every flat face, fresh and after save and reopen.
Fixes#954
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Action matrix: record the up-and-down join designs
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
- A new cut was clipped against the panel with every one of its cut-outs, so
each hole of a perforation cost the square of all the holes before it and the
second cut of 500 ran out of the flat budget. A tool is now clipped against
only the cut-outs whose boxes meet its own (the same result).
- The planar booleans' point-in-loop test now skips loops whose box is clear of
the point, before the costly on-the-loop test; with a thousand holes that test
was most of the time.
The 1000-hole panel now takes about 15 s instead of failing.
Co-authored-by: jonaswre <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
On a large thin sheet the probes around the fixed point stepped clean through
the sheet (twice the mesh tolerance of a 465 mm part is more than its 0.8 mm
thickness), so a point exactly on the face touched no material and the fold
was refused. The probes now also step a quarter of the thickness.
Co-authored-by: jonaswre <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Rounded Rectangle sketch tool (#891)
A new SKETCH > CREATE command, sketch.rectangle.rounded, in the Rectangle
family: two opposite corners and a corner radius make a 2-point rectangle
whose four corners are filleted alike, as one undo step. The radius is one
parameter (one radius dimension, the other arcs equal to it), so changing it
changes all four corners. While drawing, Width, Height and Radius boxes take
typed values; typed width and height dimension the overall size between
opposite sides. Without a typed radius the corners get a fifth of the shorter
side.
Fixes#891
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Rounded Rectangle in the Simplified Chinese catalog
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
Session::replace_design keeps auto_project when file.new, doc.open and doc.recover swap in another design, and the UI keeps it across tabs, adopt and the last-tab close. Regression tests in engine (sketch_project) and ui-egui (documents).
Offsets picked faces along their normals into a new surface body: planes and cylinders move exactly, other faces get a fitted B-spline within tolerance, and offsets that would fold over are refused. Adds the SurfaceOffset feature (noted under format 18), the surface.offset engine command and an Offset Surface dialog.
Closes#758.
Co-authored-by: jyviko <[email protected]>
A design with components and joints exports as a URDF robot description (file.export to .urdf, the MCP export tool, solidcraft-cli run --out, File > Export URDF...). It writes one binary STL per component in metres, links with mass, centre of mass and inertia from material density, and maps rigid, revolute, slider, cylindrical, pin-slot, planar and ball joints to URDF joints or short chains. Loops, broken joints and loose parts are reported as warnings. Options: mesh_prefix, effort, velocity. Docs in docs/urdf.md.
Each wall of a surface built from sketch curves (Surface Extrude, Revolve, Sweep and Loft) is now named after the curve it comes from, exactly rather than from geometry, so references to those faces survive edits.
Surface Loft lofts open or closed curve chains, one section per sketch in pick order, into surface bodies. Adds the SurfaceLoft feature (format 18 note), the surface.loft command, a dialog with Edit Feature support, and kernel and engine tests.
Part of #757.
Surface Sweep carries open curves and closed profile boundaries along a sketch path into surface bodies, with smooth walls along curved point paths. Adds the SurfaceSweep feature (format 18 note), the surface.sweep command, a dialog with Edit Feature support, and kernel and engine tests.
Part of #757.
Surface Revolve turns open curves and closed profile boundaries about a sketch axis into surface bodies, with cone apexes and sphere poles where a chain ends on the axis, and a closed shell made solid. Adds the SurfaceRevolve feature (format 18 note), the surface.revolve command, a dialog with Edit Feature support and analytic kernel and engine tests.
Part of #757.
A lip picked on a face that isn't a shelled body's rim, such as the Sample Plate's top
face with its two holes and the boss standing on it, ran its band round the largest inner
edge. That was the boss's foot, so the band stood against the boss's wall and the join
failed with a boolean error about curved faces.
The band now goes round the face's opening (an inner edge with no material just over the
face inside it). A rim face that has a smaller hole in it still works. A face whose inner
edges are only where other features stand on it, or whose openings are alike in size (a
plate's holes), is refused with a plain message that names the rim face it needs.
Fixes#892.
Co-authored-by: Claude Opus 5.5 <[email protected]>
Hole centres from a sketch now drill into the material on whichever side of the sketch plane it lies: material the spot starts in wins, then the nearest body ahead, else against the sketch normal as before. A sketch on a part's underside or below it now drills up into the part. Covers counterbores, through-all, edge and corner centres, patterns and reopening.
Delete Face takes heal (default true, as before). With heal: false the picked faces are removed and the gap stays open, leaving the remaining faces as a surface body (kernel remove_faces); deleting every face is refused. Saved only when false, noted under format 18.
Display meshes after opening, the face names read when a feature finds a face by name, and inspect.measure over all bodies are now worked out per body on plain scoped threads (solidcraft_kernel::for_each_on_threads / map_on_threads), in body order and with the same results; the browser build stays serial.
A sketch text gets an optional style: bold and italic faces (a slanted fallback for italic), left/center/right alignment, letter and line spacing, and a path curve of the same sketch for the baseline to follow (reverse takes the other side). Edit Text gets B/I toggles, alignment, spacing fields and a Path chip, all live. The style is saved only when not plain and is noted under format 18.
Renaming a body used to replace every string in later features equal to its old name, including sketch text, plane and feature names and expressions. Now only values under keys that name bodies (body, bodies, target, targets, tools) at any depth are rewritten, with a test that a sketch text spelling the body's name stays while a move follows the rename.
A hole drilled square to a flange's panel, not only the base's, is now a flat cut-out of the sheet: it unfolds with its panel to where the bend allowance puts it, shows in the flat pattern and DXF as a circle, and survives unfold and refold. A pocket tool spans the cut-outs already inside it (a counterbore's hole), so the order they are made in no longer matters. Fixes#560.
When an extrude cuts with profiles whose outlines stay more than 1 µm apart (the letters of a text), their tools are apart too, so they are joined and cut from the body in one boolean instead of one per profile. A ten-letter text cut drops from about 13 s to 1.5 s with the same result. Sheet metal targets and touching profiles keep cutting tool by tool. Tapered extrudes are unaffected.
Agent tool calls (MCP, and bridged control requests carrying allow_paths) reach files only in the open design's folder (strictly inside home or the temporary folder, not in a hidden folder, and never its hidden files), the app's recovery folder, the server's private scratch folder and each --allow-path; --allow-any-path lifts the limit. Paths are resolved first, so .. and symlinks that lead out (including a save through a link, #845) are refused. On Windows, UNC, device, NT, verbatim non-drive, drive-relative, alternate-stream, reserved-device and 8.3 short-name paths are refused before any file system call, and the resolved path must be on a local drive. doc.recovery_discard and doc.recover {discard} delete only real recovery entries. Docs: mcp.md, control-protocol.md, README.
A Sketch Palette toggle (sketch.options show_construction) that hides construction geometry from drawing and picking; saved with the sketch's view options under format 17.
Co-authored-by: William Dunn <[email protected]>
surface.extrude sweeps open curve chains and profile boundaries along the sketch normal into a surface body (walls only, no caps). Saved under format 17.
Refs #757
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Icons for the surface toolset, and its planned commands registered and disabled with the issue that tracks each one.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Sketch Move gets a toolbar placement in Sketch > Modify and a Move/Copy tool window with X and Y distances, an angle, an optional centre point and a Create Copy flag, replacing the context-menu route that ran the command with no parameters.
The feature history can sit in a panel on the left, with folders that hold one unbroken run of features, drag and drop as one undo step, and a resizable divider. Timeline folders save under format 17.
A sketch's link to a projected edge now keeps the edge's persistent name and finds it by that name when the body changes, instead of taking whichever edge ends up nearest its point.
selune