The Home page returned from the frame before the Preferences window was
drawn, so the gear, Ctrl+, and Home's Preferences / Keyboard Shortcuts
links only set the flag and the dialog appeared after leaving Home.
Draw the Preferences window on Home too.
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Snap 3D bridge drawing to points on visible sketch planes
* Keep cross-sketch point picks out of sketch tools
`pick()` returned every visible sketch's points while 3D drawing was on,
so `sketch_point_at` and the sketch tools could take another sketch's
point as an active-sketch local point plus id (flattening it or making a
bad coincident reference). `pick()` is local again; the bridge snap uses
`pick_3d` explicitly and hover mirrors it for feedback. `sketch_point_at`
also ignores foreign points defensively.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* test(sketch3d): check local point scope with a sketch tool active
Main's Project preselection fix now offers other sketches' points to idle
selection, so assert the local scope where it still applies.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* style: rustfmt
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* test: reproduce #266 (Multi-profile solid.extrude with body_name names only the first body)
* fix: name every body of a multi-body feature after body_name (#266)
A new-body feature that makes more bodies than it was given names now stores Ribs (2),
Ribs (3)... for the rest instead of falling back to generic BodyN names. Command-time only:
saved designs keep their names.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
* fix: keep body_name list for the multi-body naming step (#266)
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* test: reproduce #264 (Sheet metal: collinear tabs cannot be folded or flanged together)
* fix(sheet): fold and flange tabs that sit side by side on one line (#264)
A fold's bend zone and a flange's setback were cut with an infinite line, so
a second tab on the same line blocked a fold ('slanted or curved edge') and
two tab-end flanges in one feature shared one trimmed edge (nonmanifold).
When the zone falls apart into pieces, fold only the pieces the fold points
span, each as its own bend; trim a flange's setback only from the material
along its own edge, and attach each flange to the edge it was picked on.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
- Remove xtask/data/fusion-catalog.tsv and xtask/data/fusion-ids.tsv.
- Remove the legacy command-id table (crates/engine/src/legacy_ids.rs) and its use in
find_command and in the shortcut, recents and pinned-command loaders. Only SolidCraft's
dotted ids name commands; any other id is an unknown command.
- Boundary Fill's id becomes solid.boundary_fill.
- Replace the parity report with SolidCraft's own feature checklist: `cargo xtask features`
writes docs/features.md from the command registry.
- docs/oracle.md, docs/step-import.md (corpus section) and docs/iges-import.md: reference
results are being rebuilt on analytic and open-source (FreeCAD) values; see #292.
`cargo xtask oracle` and `cargo xtask step-corpus [--iges]` write these placeholders.
- AGENTS.md, CLAUDE.md, CONTRIBUTING.md, README.md, ROADMAP.md and the book describe
SolidCraft as independent, with reference tests on analytic values and open-source tools,
and agents do not drive or extract data from commercial CAD products.
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
Co-authored-by: Claude Opus 5.5 <[email protected]>
* test: reproduce #261 (Rectangular pattern of a hole cut scales super-linearly)
* Patterns of many hole cuts scale near-linearly (#261)
Two quadratic costs:
- Meshing a face tested every point against every segment of every boundary
loop, so a plate face with hundreds of holes meshed in quadratic time. The
vendored truck-meshalgo inside test now skips loops whose parameter box is
clear of the point (they wind zero times around it).
- A pattern cut each copy in turn, rebuilding and re-checking an ever more
complex target per copy. Copies whose boxes are clear of each other are now
one tool of many pieces (kernel::union_apart, no intersection work), cut once.
512 holes now take ~7 s instead of not finishing. The test's volume tolerance is
widened from 1e-6 relative to 0.1 % of each hole: the measure meshes the bores
and reads each hole ~0.06 % small, on main too.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Hole-pattern test: a budget CI can meet; coarser apart-box meshes (#261)
CI runs every test binary at once and is about ten times slower than a
machine running this test alone (15 tests passed 60 s in the last run), so the
512-hole pattern (about 6 s alone) hit the 60 s timeout there. The budget now
only has to tell linear from the quadratic hang: 300 s timeout, 120 s budget.
union_apart meshes each copy coarsely (2 % of its size, box grown by twice that).
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Hole-pattern test checks the scaling, not a wall-clock time (#261)
CI runs every test binary at once: the 512-hole pattern (about 6 s alone, 10 s
CPU single-threaded) took 177 s there, so no fixed time is reliable. The test
now patterns 128 and then 512 holes and requires the second to take under 8x
the first (linear is 4x, measured 3.5-4.2x here; the old quadratic cost was 16x
or more), each with the volume check and a 900 s hang guard.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* test: reproduce #268 (Panic from truck-topology lib.rs:186 when joining struts that end on a bore wall)
* Sew refuses edges whose ends weld to one vertex (#268)
The sewer welds vertices on a 1e-6 grid but only rejected edges shorter than
1e-9, so a sliver edge between the two welded its ends into one vertex and
truck-topology panicked ("Two same vertices cannot construct an edge") inside
the guard. Such an edge is now a degenerate-edge error before any truck call,
and the boolean takes its usual fallback.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Create ko.json
* Update ko.json
* Update i18n.rs
* Fonts: add a Hangul fallback so Korean doesn't render as boxes
Only the first CJK font found was loaded, and on Windows and macOS that is
a Japanese font without Hangul (Meiryo, Hiragino). Load the first readable
font of each group: the existing CJK list, then Malgun Gothic (Windows),
Apple SD Gothic Neo (macOS) or Nanum Gothic (Linux). Also rustfmt the
Korean catalog test.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Reject ambiguous origin and construction plane names
* Reserve origin plane names for construction planes; suggest the other alias
A construction plane can no longer be created with or renamed to XY, XZ, YZ, Top, Front or
Right, so a plane argument can't become ambiguous in new designs. For older designs that
already hold such a plane, the ambiguity error now also names the origin plane's other
alias (XY for Top...). The existing tests build those legacy names directly.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* test: reproduce #265 (Renaming a pattern copy renumbers the remaining copies)
* fix: renaming a body keeps its sibling bodies' names (#265)
body.rename pinned only the names of the feature's bodies before the renamed one, so unpinned
pattern copies after it were renumbered into the freed name. Pin every sibling's current name.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* test: reproduce #263 (sheet.fold accepts a fixed point that is not on the sheet)
* fix(sheet): refuse a fold's fixed point that lies off the sheet's material (#263)
A fixed point inside a cut-out or outside the base outline (in the panel's
thickness) silently picked a side. Refuse it with an error that names the
point; side-face picks and points on other panels keep working.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
The oracle no longer uses Fusion measurements. tests/oracle/<case>/ now holds the 76 recipes
(our own format, with recorded measurements and tool-specific fields removed) and an
expected.json per case:
- 55 analytic cases: closed-form values from tools/oracle-analytic/ (stdlib Python, formulas
in each case's "method").
- 21 FreeCAD cases: the same recipe built with FreeCAD's public scripting API by
tools/freecad-oracle/ (an external program, not a dependency), with a reference.stl for 20.
solvecraft-cli oracle compares body count, volume, area, centre of mass, bbox, face counts
where the geometry fixes them, and, against reference.stl, the sampled Hausdorff distance and
the principal moments (spatial.rs from #301). cargo xtask oracle reads tests/oracle, writes
docs/oracle.md with the source of each value, and supports known_failure marks for tracked
bugs. CI runs it on every PR; a manual workflow regenerates the FreeCAD values. step-corpus,
seam normalisation and the through-all emulation, which only existed to compare with Fusion,
are removed.
75/76 pass; 75-sm-bracket-holes is a known failure (#296).
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
Navigation presets are now a table of bindings (button, required modifier
keys, camera mode) instead of string matches. The Alias preset binds
Shift+Alt+left to orbit, Shift+Alt+middle to pan and Shift+Alt+right to
zoom. A left press with a binding's keys is latched until release, so that
drag neither box-selects nor drags sketch geometry; plain left drags behave
as before. Shift only requests snapping when the binding without Shift
still orbits.
The scenario harness sends Alt with ui.drag/ui.click, and camera checks can
assert panned/zoomed since the last camera step. The user guide notes Alt+drag
grabs by KDE and GNOME and how to free them.
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Toolbar drop-downs highlight the row under the pointer and the keyboard focus (#288)
A panel drop-down's command rows are full-width rows that take the theme's hover background
(icon, label and shortcut on it) when hovered or focused. Up/Down move the focus through the
enabled rows, Enter starts the command, Escape closes the drop-down. Rows publish
`dropdown:<id>` and the highlighted one `dropdown_hot:<id>`; scenario s46 checks pointer and
keyboard highlight.
Fixes#288
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
* Toolbar: drag commands from drop-downs onto the toolbar; pin icon; Customize Toolbar… (#289)
- A panel drop-down row drags onto the toolbar (a button or a panel's free space, with the
drop line) and is pinned there; the dragged command's icon follows the pointer.
- A toolbar button dragged off the toolbar, or back into the open drop-down, leaves it (its
icon shows a cross while releasing would remove it).
- A hovered drop-down row shows a pin at its end: click to pin or unpin.
- Right-click on the toolbar's empty space: Customize Toolbar… (a window listing the tab's
commands with check boxes, and Reset Toolbar) and Reset Toolbar; command menus have
Customize Toolbar… too.
- Still per workspace and tab, kept with the preferences. Toolbar buttons also publish
`button:<id>`; scenario s47 drags a row to the toolbar, unpins by dragging off and into the
drop-down, uses the pin icon and Customize Toolbar…, and checks it survives a restart.
Fixes#289
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
* Toolbar drop-down pin: a push pin drawn in code (upright and filled when pinned); control protocol lists the toolbar handles
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Appease X11 users with niri/wayland specific postfixup wrapper
* Linux: stay on native Wayland under niri in the app, not the Nix wrapper
Move the niri check from the flake's wrapper into apps/solvecraft/src/main.rs
next to the XWayland default, so it applies to every niri user, not only
Nix builds (flake.nix is back to main's, which also clears the conflict
with #210). SOLVECRAFT_WAYLAND=1 still keeps native Wayland, and =0 now
forces XWayland. docs/nix.md notes the trade-off: no file drag-and-drop
on native Wayland.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Fillets along a straight edge between two cylinders: the rolling-ball blend trims curved cap edges to its contacts
The edge where two overlapping extruded arcs meet is a straight line between two cylinders
ending on planar caps. The rolling-ball blend built its sections and surface, but only
straight seams could be shortened to the contacts, so a circular cap edge was refused with
"a curved edge where the blend ends". Curved seams now keep the part of their curve between
the new ends, found from the nearest of a few samples (a search from the far end of a long
arc can settle on the opposite side of the circle).
The ball's surface projections start from each face's last answer instead of a cold search,
falling back to one when the warm answer leaves the surface's parameters or is farther than
the last point: about 4.5x faster per fillet (370 -> 80 ms), so dragging the radius is usable.
Fixes#237
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Curve blend: refuse a closed curved seam where the blend ends
A seam that starts and ends at the same vertex (a full circle) has no
"between" two contacts, so trimming it built a broken edge. Return
"not supported yet" instead. The curved-seam trim moves into
trim_curved_seam so it can be tested directly.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
Co-authored-by: bherbruck <[email protected]>
* test: reproduce #262 (sheet.fold: bend zone reaching the blank outline is reported as a slanted or curved edge)
* fix(sheet): name the bend zone reaching an outline corner instead of blaming a slanted edge (#262)
A fold whose bend zone contains a corner of the panel outline (a fold at a
tab's root) was reported as crossing a slanted or curved edge. Name the
corner and how far to move the fold line to clear it.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Expose interactive editing and placement of sketch text
* Respect document units when editing sketch text
* Route Edit Text through the shared feature dialog
The sketch text editor is now a Kind::Text dialog opened through
Dialog::for_command (frame.rs docking, standard OK/Cancel, Enter/Esc).
Its fields are ordinary dialog fields: they take expressions, parameters
and units, and bare lengths are in the design's units. Untouched fields
keep their exact saved values. The dialog stays open across unrelated
design changes and closes only when its text is gone, the sketch ends,
or another command starts.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Honor design units in sketch dimensions and measurements
* fix: apply document units to specialized length controls
* Accept explicit units in length fields; document design-unit dimension values
Length fields in a design-unit control now evaluate what is typed as a
length expression: a bare number stays in the design's units, while an
explicit unit ("10 mm", "0.5 in", "1 in + 5 mm") is converted.
Document that a bare numeric sketch.dimension value from scripts, the
control channel or MCP is read in the design's units.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
- The dialog draws every page into a fixed, clipped 744x400 area, so no page
(or translation) changes the window width; descriptions wrap and tall pages
scroll inside it.
- OK / Cancel / Apply sit flush right in the bottom bar (right-to-left layout
within the fixed width); Restore Defaults stays left.
- The "settings" icon is a gear: a solid ring with six square-ish teeth and a
see-through centre hole, instead of the sun-like rays.
- Scenario s46 visits every page and checks the window keeps its width and
that Apply ends at the bottom bar's right edge (new `same_width` and
`right_edge` scenario checks).
Fixes#290
Co-Authored-By: Claude Opus 5.5 <[email protected]>
sheet.flange now lists name?/body_name?, solid.loft and solid.sweep list
targets?/name?/body_name?, and the primitives list name?/body_name? (all go
through add_feature, which reads them). A test pins the shared keys for
every body-creating feature.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
Params docs name other commands ("usable in sketch.delete"), so filtering by
an id returned 56 commands. The filter now looks only at id, label, tab and
panel; the tool description and docs/mcp.md say so.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
- Web: a failed CJK font fetch shows English for this session only; the
saved language preference is kept (CjkFontLoader, persisted on save).
- Web fetches the CJK font only when a CJK language (ja) is selected.
- fonts.rs: directory scans match CJK-specific names only (no "noto" or
"gothic"); CJK stays the last fallback after the Latin UI font.
- Revert unrelated clippy rewrites in component_clone.rs, coplanar.rs,
canvas.rs and issue_report.rs to match main.
- Tests: default English, fallback order, CJK-only matching, fetch only
for CJK, failed fetch keeps the saved language.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01RjGw4gA5ZvKrU8MQP6sBgT
- Bundle BIZ UDPGothic Regular (SIL OFL 1.1) exclusively in solvecraft-web dist
- Remove external jsDelivr CDN fallback; fetch font solely from same-origin ./fonts/
- Fetch Japanese font on-demand only when UI language is set to Japanese
- Gracefully fall back to English UI on fetch failure to prevent tofu glyphs
- Update ATTRIBUTION.md, NOTICE, and THIRD-PARTY-LICENSES.txt
certify_nesting runs two planar booleans per pair of boundary loops, but
its work budget counted segments, so a mesh with many small holes could
trigger ~1M booleans. Refuse more than 50 loops (1225 pairs) with a
"too complex to convert" error and test a 400-hole plate.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
With Object Type = Bodies, the Mirror, Rectangular Pattern and Circular
Pattern dialogs sent the feature that created each picked body
({"features": ["Extrude1"]}), so the copies replayed only that feature and
lost everything done to the body afterwards (a fillet, a chamfer, a cut).
They now send the bodies themselves ({"bodies": [...]}), which the commands
already support and the Path Pattern dialog already did. Picking Features
is unchanged.
Editing a body Mirror or Pattern from the timeline now reopens the dialog
with its bodies selected.
Copies made this way take the body-copy names ("Body1 (2)"), as the
commands already give; pattern_direction_edge now looks up "Body1 (3)".
Tests: UI scenarios mirror_body_keeps_fillets and pattern_body_keeps_fillets
(filleted cube, copy and edit through the dialogs); both fail without the
fix with the copies' sharp 8000 mm3 volume.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
construct.plane.offset now takes a planar face as its base
({"face": [x,y,z], body?, index?, path?}), captured with the same exact
face attachment a sketch on that face uses. The Offset Plane dialog accepts
planar faces as well as origin and construction planes.
A construction plane on a face is resolved through its face anchor when the
timeline is evaluated, so it follows the face when upstream features change
(and after reopening), instead of keeping the plane as it was when picked.
Tests: engine (top and side faces, follows a box resize, survives reopen,
hostile picks are refused without adding a feature) and a UI scenario that
picks a face in the dialog and builds a pad on the new plane.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Add aarch64-darwin to the flake systems so packages, apps and both
devShells are exposed on Apple Silicon Macs. The Wayland/X11/EGL
runtime libraries, the /run/opengl-driver search paths, the freedesktop
packaging and the wrapProgram post-fixup are Linux-only and stay that
way: on macOS winit talks to AppKit, wgpu renders through Metal, and
the GPU drivers ship with the OS, so the darwin package needs no
wrapper. x86_64-darwin is deliberately not added: current nixpkgs
unstable no longer evaluates rustc for that platform (26.11
deprecation), so the package would fail on toolchain evaluation.
docs/nix.md: platform list updated, macOS paragraph in the graphics
section, desktop-entry paragraph qualified as Linux-only.
