inputs_mut, inputs and expressions are now built on one exhaustive walk (walk_exprs / walk_exprs_mut) instead of two hand-written matches over FeatureKind. inputs() no longer clones the feature, plane chains are walked with the same nesting cap for inputs as for expressions, and a new variant without a walk arm does not compile. A golden record of every variant's expressions guards the walk.
docs/mcp.md gains a "Camera and close-up recipe" section: the orbit camera's conventions (radians, eye direction for yaw and pitch, orthographic half-height, which side inspect.section keeps) and a seven-step recipe for a close-up of one region of a large STEP model. Documentation only.
* Fillets and chamfers meeting at corners on curved faces, on top of #935
What #935 and #926 leave of #851 and the matrix:
- Corner build for blends meeting on faces of any surface (curvecorner.rs):
the knife-edge tip's round with the arc's or the back edge's, edges
picked in any order, a round ending in an earlier round of its radius
(as a feature of its own), and chamfers meeting at the arc's corner.
Its end curves are fitted by chord length: a uniform parameter
through points clustered at the ends doubled back on itself there,
and the display planner refused the face.
- A straight edge ending at a curved face (the back edge into the
knife-edge tip): rolled, or cut by the face in the planar corner
build (blend_corner.rs).
- A rolling ball turning about a rounded corner of its own radius
(a pivot: a piece of sphere or cone).
- Seams that are an earlier blend's straight contact (fitted curves)
count as straight.
- No spline across a joint where the strip's curvature jumps (a line
into a small round): each strip ends on the joint's section.
- Sections at a chain's vertices on the faces of the edge from it
alone.
- Every new fillet path passes #949's check for openings.
Tests measure volumes through the display plan, as #935's do.
Action matrix: 51 more fillets and chamfers pass (sweep, tangent arc
chain, sheet-metal hem, bracket holes), none fewer. Robustness seed 33
recorded (its last fillet builds differently; display and measured
volumes now agree).
Co-Authored-By: bherbruck <[email protected]>
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_015bV2ntwLfUHV4JnCMPSyRi
* Corner blend tests: scale, seed 33's volumes, tighter engine bounds
From the review of #854:
- seed_33_display_plan_and_measure_agree: seed 33's bodies measure
the same through the display plan and the measure (2e-5), which the
golden's re-record rests on.
- the_arc_rounded_after_the_back_edge_matches_both_together: the order
that still leaves 0.05 mm³ at the tip, as an ignored test.
- corner_blends_hold_at_any_scale: the cases this branch adds on the
#851 part, at 0.01x and 100x, take off what they take at full size
times k³ (within 5e-6, checked to 1e-4).
- The engine tests on the part as drawn measure through the display
plan; bounds are about twice what each reads (2e-4 to 3e-3), and the
front corner's sets are checked against the kernel's CSG grid.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Claude-Session: https://claude.ai/code/session_015bV2ntwLfUHV4JnCMPSyRi
---------
Co-authored-by: bherbruck <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
press_pull_on_the_enclosure_lid_is_prompt took 61-87 s of wall time on loaded runners against a 60 s bound, for about 9 s of CPU. It now checks the operation's CPU time (under 300 s) and how far it grows the peak memory (under 1 GB; the runaway it guards against passed 24 GB), from /proc/self where the system has it.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
The sampled pi-case hole on Body1/F13:side:[email protected] became a real hole with #952 (7.5 s instead of 170 ms); beside the heavy tests on main's push runs it passed the matrix's 90 s action limit in its edit round, reported as the design not loading. The sample now takes every CPU in nextest so nothing runs beside it, and the edit round writes a start line so a hang there is reported as <action>+edit.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Adds the read-only material.properties.validate command: schema_version 1 engineering material cards in SI units are checked for numerical consistency and elastic stability, with derived isotropic moduli, missing conditions and sources needing review. Nothing is assigned or saved.
Thanks @0xlillith.
Fixes#971. At the node limit the offset certificate splits the fitted curve where it meets the exact offset midpoint, so curves with different parameter speeds certify within the same 0.002 mm tolerance. Associated offset fit nodes are hidden from display, picking, box selection and snapping until Break Association.
Thanks @Karl-VonRichter.
#970's lenient retry of a face's parameter boundary searches the whole surface as a last resort; on robustness seed 20 it found an edge's points across a cylinder's seam, half a turn apart, and the Cut failed. A lenient boundary whose points jump half the parameter range or more is refused, and the face is left undivided as before (#970's elbows step at most a fifth of the range). Seed 81's volume moved by 0.1 mm3 with #952's hole direction; recorded.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Fixes#928. Extrude To / From Object and Revolve To Object now resolve their target in the feature's own component frame, so a face in another component whose occurrence is moved is found where it is shown instead of the extrude stopping at a flat plane through the picked point. The point is named after the nearest face, a named point keeps its named face when another component touches it there, and such features re-evaluate when a placement changes, so they follow the target when it moves later.
Co-authored-by: SychPL <[email protected]>
Fillet gets a Curvature (G2) radius type (type: "curvature", alias "g2"): a quintic blend whose size is the equivalent circular setback, for convex and concave straight edges between planar faces with a perpendicular planar end face at each end. Unsupported cases are refused rather than falling back to a circular fillet, and a blend that would cross a loop in its end face is refused. Persisted as a fillet style under format 19; labels in en/de/ja/ko/zh.
Co-authored-by: midasdf <[email protected]>
Touching sews now split 4-use straight edges on extruded walls (along their rulings), not only on planes. Faces round such an edge are ordered by the way they leave it and, where they leave it tangent, by their curvature. Sheets bound the material wedges as before, except where that would make a face touch itself (a hole touching the outline from inside); edges ending there pair the empty wedges instead, so each loop gets its own vertex. Coincident faces are still refused, plain sew still refuses vertex contact, and shell_groups is unchanged.
A Ø10 hole tangent inside a stepped Ø40/Ø20 boss now cuts exactly instead of failing with "wire is not simple". Robustness seeds 42 and 51 are recorded: their touching hole patterns in stepped bodies now cut exactly instead of by a tool nudge.
Co-authored-by: froglemonade2 <[email protected]>
The CPU renderer's line depth test allowed a fixed share of the scene's depth range (2e-4), which on large designs or close views let edges a millimetre or more behind thin sheet show through it. Each pixel now keeps the screen depth slope of the surface it shows, and a line passes where it is no further behind than that slope spans across the line's width, plus f32 rounding. Section caps use their plane's slope.
Edges lying on steep faces now draw their full width; edges behind a face stay hidden. Only crates/render/src/raster.rs changes; the GPU viewport is unchanged.
Co-authored-by: NOWN-DEV <[email protected]>
* Boolean nudge tried both ways: no sliver where a cut's end touches a round side (#897, #827)
Robustness seed 14 cuts a cylinder whose end lies exactly on the apex of the
plate's arc side. Since the display tessellation plans (#805) the generator sees
the arc's true extent, so the cut's base lands on -10 instead of -10.000000000000002
and the end is tangent to the arc. The direct boolean fails there and the
last-resort tool nudge pushed the end into the arc, leaving a planar sliver a
tenth of a millimetre wide; shell then picked that sliver and refused it. The
13 October merges were not the cause (the bisect lands on #805).
The nudge is now tried both ways and the simpler result (fewer faces) is kept,
so the opposite nudge parts the touching faces instead. The same change joins
the hinge barrel in #827, whose top lies tangent to the lid's underside where
the mounting leaf ends. Each result still passes the same checks as before.
Goldens: seeds 14, 26 and 85 now build to the end, 31 and 78 come out with
fewer faces. Seeds 6, 43 and 73 still stop at shell: their joins now succeed and
shell reaches corners it can't offset (a cusp where a box face touches an arc,
coplanar faces facing opposite ways), which is unchanged.
Fixes#897Fixes#827
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Nudge the other way only when the first nudge fails or leaves a sliver
Trying both nudges and keeping the one with fewer faces could prefer a result
that keeps two pieces joined by a hair over one that separates them (the
centred coplanar revolve cut). The opposite nudge now runs only when the first
one failed or left a face narrower than 1/200 of the part, and it is taken
when it works with fewer of those.
Goldens re-recorded on current main: seeds 14, 26 and 85 build to the end,
31 and 78 with fewer faces. The other changed seeds are main's own since its
last full record, identical with and without this change.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Nudge the other way only for slivers the nudge made
On the sensor enclosure's lid the first nudge left thin faces the operands
already had (thin walls, small rounds), so the opposite nudge ran a second
boolean for nothing and the press/pull took 79 s against main's 55 s. The
opposite nudge now runs only when the first one failed or left more slivers
than the operands brought; the press/pull test takes 36 s against 42 s on main
(same machine, one after the other).
Goldens re-recorded on top of #940.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Goldens on current main: seeds 31, 43 and 78 with the two-way nudge
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Keep the hinge and tangent-cut tests beside the #871 fillet test
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Goldens: seeds 33 and 91 as main's fillet changes build them
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Goldens: keep main's #950 record
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
The state probe opened every cache it listed; when a worker deleted one in between, the open made it again, empty, and the next wait timed out. The probe now reads each cache with caches.match over the builds' files and marks, which never makes a cache (3 failures in 20 runs before, 0 in 30 after). The worker only ever starts a complete build.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
Trimming the base at an edge flange's setback snaps corners within tolerance onto the trim line and merges away the zero-width run a ledge as tall as the setback left along it, so the ledge goes with the strip as a lower one does. Splitting outline edges at other cells' corners now skips points within the model's tolerance of an end, so a ledge a little taller keeps its sliver and the bend runs under it, also off the axes. Both used to fail with "sew: a degenerate edge". Nothing new is stored.
A hole drilled along a panel, into its rim, has no place in the flat pattern
as a cut-out, so every such hole was refused. It is now kept as a bore of that
panel, in flat coordinates, and cut only from that panel's material when the
folded part and its flat pattern are built, so the sheet still unfolds and
folds back with it. A hole that would run into a bend, or cross a panel at an
angle, is still refused. The flat pattern lists the bores.
The action matrix worker takes ACTION_MATRIX_ONLY (just these actions) and
ACTION_MATRIX_UNFOLD (unfold and refold every sheet after each action) for
rechecking one group by hand.
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Holes on round faces from the app, one hole per pick, and Flip for holes at sketch points (#967)
The Hole dialog takes any face: a hole on a round face drills against the face's normal where it
was picked, and its arrow shows that. A round face split at its seam is picked whole, but makes
one hole where it was clicked. Holes at sketch points get Flip (saved as flip in the hole's points,
under format 18), in the command and in the dialog.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Holes at sketch points show their arrow: into the part, or away with Flip (#967)
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
Sketch Mirror, rectangular and circular Pattern, and Offset now show a green live preview that follows the selection and settings; OK commits, Cancel leaves the sketch unchanged. The shared dialogs show the current selection step and source counts, sources can be toggled with Ctrl/Cmd-click, cleared and reselected.
Offsets keep editable driving distance dimensions (One Side, Two Sides, Symmetric) that update the derived curves without moving the source, with undo/redo and save/reopen. Format 19: older files keep their fixed offsets.
New dialog labels in en, zh, ja, de and ko.
Fixes#696. Fixes#517.
Cutting one lofted round tube from another failed in truck's divide_face ("parameter boundary") for some section counts: the intersection points lie on the loft's seam, the previous point's parameter can sit a hair outside the range, and the Newton search from there fails.
The boundary is built as before; only when that returns None is it built again leniently, starting each search from the hint clamped into the parameter range and, as a last resort, searching the whole surface. Nothing that succeeds today changes. The boolean-retry guards are untouched.
Fixes 5 of the 6 failing hollow-elbow cases in #968 (new test crates/engine/src/tests/loft_cut.rs, volumes within 0.3% of exact). 90 degrees / 14 sections still fails in a later step and stays open in #968.
The plate check compared the face outline's area (from the tessellation, so each hole was a polygon of chords) with the exact volume, and refused plates with a few small holes. Where the outline runs along a cylinder about the plate's normal it is now an arc of that circle; coaxial pieces of one radius are one wall, so a hole split into two, three or four faces is one circle. The check passes with its tolerance unchanged, and the flat pattern and its DXF carry one CIRCLE per hole (ARC for rounded corners and slot ends).
A round blank now converts too, so unfold_cut_refold_and_convert checks the refusal with a block thicker at one end instead of a rod.
* Hole matrix: placement, types, extents, edits and 0.9.0 designs, with today's failures listed
Each case checks the drill goes into the material, the bore sits on its axis, a blind hole stops
where it should, the removed volume against its analytic value, the face count and that every
body is still one closed valid solid. Failing cases are listed in tests/hole_matrix/known_failures.txt
as a ratchet.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* A hole on a face drills into the material, also in older designs (#950)
Without a direction, solid.hole took the direction from any face whose infinite plane passed
within ten tolerances of the point, the last one found winning: the far side of a thin plate or a
face of another body at the same height could set it, and the wrong direction was saved. It now
uses the face nearest the point, against its outward normal (exact for planes, cylinders and
spheres, so holes on curved faces work without a direction). When a design is evaluated, a face
hole whose saved direction leaves the face it starts on is mirrored into it, so designs saved
with the wrong direction drill into the part.
Fixes#950.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Hole at a point on no face (a planar face's centroid outside it) keeps the plane it lies in
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Record the hole direction fix in the goldens and the action matrix baseline (#950)
Seeds 7, 21, 81 and 85 drill their holes straight into their faces now. In the action matrix,
holes on four faces that used to go the wrong way now build, and two whose correct direction
meets a cut the kernel refuses are marked failing.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Goldens: seeds 7, 21 and 85 drill their holes straight in (#950)
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Fillet: refuse a result with openings in its surface (#871)
A fillet on #871's part (radius 1 on a window's edges and on the sides of a
block 1.26 mm away) came back closed as topology with every face meshing, but
the rounds overlapped and the end faces' boundary loops crossed, so the model
showed holes. The constant-radius fillet now checks its result before taking it:
the body's mesh, welded within a millionth of its size, must have no edge
without as many triangles running the other way along it, except for cracks
within the mesh tolerance where fitted curves meet. A result that fails is
refused, so the corner build gets its try and the radius search treats it as
too large.
Body::open_mesh_edges is the check. Kernel tests cover the #871 part (refused
at radius 1, closed with a round on every edge at 0.5), and an engine test runs
the fillet from the report and leaves the part as it was. All 96 robustness
seeds build the same with and without it.
Fixes#871
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Check fillets for crossed face boundaries, not free mesh edges
Free edges in the mesh also come from cracks where fitted curves meet (corner
patches, rounds ending on curved edges), so the mesh test refused good fillets.
The check is now on the cause of #871: a planar face whose boundary loops cross
each other or themselves has no inside. Body::crossed_face_loops samples each
planar face's loops within 1/1000 of the size and counts proper crossings
(touching within a millionth doesn't count).
The pyramid apex blend and the loft fillets build again. Ten action-matrix fillets
stay refused, recorded in the baseline: r = 3 on the 2 mm rim of oracle 09's
shelled box (the round runs past the inner wall; the result was 240 mm3 lighter
than any round can make it), and the six seam-edge fillets on oracle 60's bolt
holes, whose boundary jumps across the hole.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
PathScope stores its roots canonicalised (\\?\ on Windows, /private/var on macOS), so the default-folders test now canonicalises scratch_dir() before looking it up, like the recovery folder on the line above.
The same fix came in from @Karl-VonRichter in #969, found on macOS.
Co-authored-by: Karl-VonRichter <[email protected]>
- A fold's zone clipped across the root of a tab folded before on the same
line kept a sliver of no width there, which made the zone look like it
crossed a slanted edge. The one real piece is the zone now (#638).
- When the tabs a fold line spans can't take the side beyond them along,
because it joins the side that stays through other material (a tab on the
inside edge of an L, the fixed point on the far leg), the tabs' own ends fold
instead, the same part as with the fixed point on the near leg (#639).
Co-authored-by: jonaswre <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
* Name a side drawn on several sketch curves by all of them
An extrude named each side wall after the one sketch curve its profile
segment lies on. A wall along two coincident lines (squares drawn edge to
edge) or along collinear lines merged into one profile segment had no
single curve, so it was named from geometry and could not carry a sketch
attachment. One sketch extruded up and down and joined (the logo) refused
a sketch on every one of its side walls.
Such a side is now named by every curve it lies on, in sketch order: the
first is its name, the others aliases. The set is fixed by the sketch, so
the name is exact. The refusal message no longer blames merged faces.
Adds the reported logo design and a synthetic up-and-down join to the
action-matrix designs, and a regression test that sketches and extrudes on
every flat face, fresh and after save and reopen.
Fixes#954
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Action matrix: record the up-and-down join designs
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
- A new cut was clipped against the panel with every one of its cut-outs, so
each hole of a perforation cost the square of all the holes before it and the
second cut of 500 ran out of the flat budget. A tool is now clipped against
only the cut-outs whose boxes meet its own (the same result).
- The planar booleans' point-in-loop test now skips loops whose box is clear of
the point, before the costly on-the-loop test; with a thousand holes that test
was most of the time.
The 1000-hole panel now takes about 15 s instead of failing.
Co-authored-by: jonaswre <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
Fillets and chamfers ending on a boss's pieced wall or beside it, on a face that runs along its seam twice, and loops the loop blend refuses
- A straight edge whose end meets one curved surface in several faces (a cylinder a join left
in pieces) ends on that surface: the section is cut where it crosses each seam, which is
shortened there; where no seam is crossed (the wall missing inside the other body) the
section lies on the bared surface and the rest of the side edge becomes a seam.
- Two end faces that aren't both planes meeting in lines: each face takes the section's points
on it, cut where it crosses the edge between them. Not where an end face runs on smoothly
from a side (an earlier round): the corner build takes those.
- Face boundaries close over several connector edges.
- A face on a periodic surface running along its seam twice (as a STEP file gives it) is
rebuilt the same way (#691).
- A curved chain ending square on a face that runs on past its side extends that face's seam.
- A smooth chain stops before an edge between faces that meet smoothly.
- A loop the loop blend refuses for its shape is blended edge by edge; refusals about its size
stand.
- Action matrix: ACTION_MATRIX_ACTIONS and ACTION_MATRIX_VALIDITY for quick local runs; the
fillets and chamfers that pass now recorded.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
On a large thin sheet the probes around the fixed point stepped clean through
the sheet (twice the mesh tolerance of a 465 mm part is more than its 0.8 mm
thickness), so a point exactly on the face touched no material and the fold
was refused. The probes now also step a quarter of the thickness.
Co-authored-by: jonaswre <[email protected]>
Co-authored-by: Claude Opus 5.5 <[email protected]>
#921's grid lines through the vertices that split a ruling edge also went into the meshes Boolean operations intersect, which changed seven robustness seeds (seed 2's sphere cut failed). Deflection::rulings now asks for them only in the kernel's own tessellation (display, export, measurement). The seeds #936 (rejected instead of unsupported), #946 (26 and 85 build, others fail differently) and #921's display side (about 1e-6) moved are recorded with their reasons.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
#820 fixed examples/bracket.json's fillet pick, which lay far from every edge and rounded the outer corner instead of the inner one. This re-records examples/bracket only: its edges carry the fillet's new names, and three chamfers beside and across the inner fillet are refused (the blend is larger than the neighbouring faces).
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Rounded Rectangle sketch tool (#891)
A new SKETCH > CREATE command, sketch.rectangle.rounded, in the Rectangle
family: two opposite corners and a corner radius make a 2-point rectangle
whose four corners are filleted alike, as one undo step. The radius is one
parameter (one radius dimension, the other arcs equal to it), so changing it
changes all four corners. While drawing, Width, Height and Radius boxes take
typed values; typed width and height dimension the overall size between
opposite sides. Without a typed radius the corners get a fifth of the shorter
side.
Fixes#891
Co-Authored-By: Claude Opus 5.5 <[email protected]>
* Rounded Rectangle in the Simplified Chinese catalog
Co-Authored-By: Claude Opus 5.5 <[email protected]>
---------
Co-authored-by: Claude Opus 5.5 <[email protected]>
Each section now starts at the rotation whose vertices line up best with the lead section's, vertex for vertex, instead of at the one vertex closest in direction to the lead's first. Fixes the twisted loft of matching non-convex sections; regression test loft_pairs_the_vertices_of_matching_non_convex_sections.
Session::replace_design keeps auto_project when file.new, doc.open and doc.recover swap in another design, and the UI keeps it across tabs, adopt and the last-tab close. Regression tests in engine (sketch_project) and ui-egui (documents).
Rolling-ball blends now handle knife edges, where the two faces have opposite normals; an edge that runs out along an end face tangent to one side; and rounds that end in an earlier round on curved faces, picked together or one after another. The three edges at a vertex of smooth faces, rounded to one radius, end in a piece of sphere. When the given order of up to four edges is refused, or leaves a face boundary off its surface, other orders are tried.
Closes#851.
Co-authored-by: lasselian <[email protected]>
Adds a complete Simplified Chinese (zh) catalog covering every English message, a font fallback for Chinese text, and `cargo xtask i18n --check`, which checks that the complete catalogs (ja, zh) carry every English message and that every command label is translatable.
Co-authored-by: Noly1990 <[email protected]>
Packs the scene's planned bodies into one GPU upload and dispatch, and evaluates intersection edges by seeded Newton refinement from a fitted B-spline through exactly solved leader points, falling back to the previous evaluation near tangency. Intersection nodes carry their faces' parameters. This changes speed, not what the app draws.
Part 4 of 4 of #303.
Co-authored-by: jyviko <[email protected]>
Thicken now moves faces through the same mover as Offset Surface. Spheres, cones, tori and B-spline faces thicken as well as planes and cylinders, and a thickness that would fold a curved face over is refused. Where thickened faces meet at a sharp edge, a wall closes the gap and corners are closed with flat patches. Thickening into an inside corner is still refused with a clear message.
Closes#765.
Co-authored-by: jyviko <[email protected]>
Offsets picked faces along their normals into a new surface body: planes and cylinders move exactly, other faces get a fitted B-spline within tolerance, and offsets that would fold over are refused. Adds the SurfaceOffset feature (noted under format 18), the surface.offset engine command and an Offset Surface dialog.
Closes#758.
Co-authored-by: jyviko <[email protected]>
A section stayed on with nothing in the browser to switch it off; only the
viewport's context menu had Remove Section. While there is one, the browser
now has an Analysis folder listing it. Its eye (and the folder's) hides the
section and shows it again on the same plane; a double-click or Edit Section
Analysis opens the dialog, and Delete removes it. Browser rows with an eye
publish an `eye:<label>` handle for automation.
Fixes#822
Co-authored-by: Claude Opus 5.5 <[email protected]>
Closing a socket with unread input resets the connection, and the reset could reach the client before the refusal did (requests_run_only_after_the_token failed 17 times in 100). The server now ends its side and drains, briefly and up to 64 KiB, what the client had sent before closing: 0 in 100.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
A through-all hole's tool is twice the largest body long, and the boolean's tolerances
followed that length: a 6 mm hole through a 920 mm part was traced at nearly 1 mm, wider than
the hole, and the cut came out empty or failed. When every other strategy has failed, the
boolean is now asked again (unshifted, then once shifted) at tolerances scaled to where the
bodies meet: the overlap of their boxes and the thinner operand's thickness. Its result is
checked as the others are and held to the retry guard. It runs last, so whatever an earlier
strategy answered is kept as it was, and only for single-shell operands (bodies in several
pieces are retried a piece at a time, each with this pass of its own).
The sampled shortcut also gave up on a slender tool lying across its box (a long hole drilled at
an angle fills little of it): it now samples past the first 2000 points until enough land
inside, so a tool that misses a body leaves that body as it is. Bodies that had enough samples
in the first 2000 are sampled exactly as before.
Baseline: the 90 actions that newly pass, rechecked one by one with the final build.
Co-Authored-By: Claude Opus 5.5 <[email protected]>
A design with components and joints exports as a URDF robot description (file.export to .urdf, the MCP export tool, solidcraft-cli run --out, File > Export URDF...). It writes one binary STL per component in metres, links with mass, centre of mass and inertia from material density, and maps rigid, revolute, slider, cylindrical, pin-slot, planar and ball joints to URDF joints or short chains. Loops, broken joints and loose parts are reported as warnings. Options: mesh_prefix, effort, velocity. Docs in docs/urdf.md.
Each wall of a surface built from sketch curves (Surface Extrude, Revolve, Sweep and Loft) is now named after the curve it comes from, exactly rather than from geometry, so references to those faces survive edits.
JIJINBEI